Over 12 years? I'd like to see it!! Congratulations!! Mark in WV In Econosrus@yahoogroups.com, "geyservillebob" <itswonderful@c...> ... what ... Ever ... I ......
Thanks Mark. I need to get the hood and the headlight rings on it before I take any beauty shots The hood hinges and the rings are down at the corner body...
***That really hurt something deep inside me:( I have more to say about this when everybodys had a chance to see it if they want to. marye, sad in e Texas...
Yeah, I won't see it for another hour and a half or so. Marye <akadentedm@...> wrote: ***That really hurt something deep inside me:( I have more to say ...
I just got a new AT702 Blue-Point air ratchet to use on the DCW. Nice tool. The instructions say that the ratchet mechanism should be greased weekly. How in...
If you grease yours every week, you will undoubtedbly be the first one. I'm not familiar with that particular model but if the instructions say "grease" then...
*** I'm not going to tell you about how I dont watch (IMO) stoopid TV shows but I will say this... Tonights viewing was the main reason I dont. I've always...
That was just wrong! And you are right Marye, that was very sad. They could have just faked damaging the econo. Strange how you can get attached to these...
Hmmmm... http://buy1.snapon.com/catalog/item.asp? P65=&tool=power&item_ID=7556&group_ID=2820&store=snapon- store&dir=catalog I'll look for a hole. Frank in...
Thanks Jeff, I'll look for the hole but the dipping method would be fine by me. Frank, fretting over every little detail in Cloverdale, CA _____ From: Jeff...
Wrong doesn't even begin to describe it Jim. I was struggling with all three of my VCRs, and trying to straighten out my rabbit ears, trying to pick up the...
Yeah, that's how I've always done it too but this time I made the mistake of reading the instructions and it says. "If the tool is used daily, then the ratchet...
Frank, I've always done what Jim says, and put a couple of drops of air tool oil in the fitting when I hooked them up. If you want to get fancy you can get an...
Thanks, Lee, Jim, and Joe, for the responses on the emblems. Jim, the factory goofs did include the Econolines. I found a '62 van in the junkyard once with a...
Many times folks include a link(web address) in a message only to find that it is broken(split and unusable when clicked) when that message is posted. :( In...
Lubrication of the air motor by dropping air tool oil (I use ATF there too) into the fitting is a good idea of course but the head with the ratchet mechanism...
The HEAD HAS TO BE GREASED, you can buy a simple grease gun for this purpose the dealer shoud have them. the grease hole is on the neck holding it away from...
Hi Group, I have a pointer type torque wrench but want to buy a nice set and click type. I only want to buy one at this time, and I have both half and...
I have a very old and reliable (I think) Proto 1/2" drive foot pounds wrench and a El Cheapo 3/8" drive inch pounds wrench. I don't have a lot of confidence ...
Mark, Buy the 1/2" drive. You'll get more use out of it. To prolong the life of the torque wrench, no matter which size or brand, be sure to release the...
The pointer type is more accurate, and will remain so longer than the clicker type. Be sure to compensate for using adapters (or extentions)from the 1/2 to...
The whole blacked-out Econoline emblem definitely differs from the paint on the one I was talking about. I'll see if I can scan it tomorrow. FWIW: the CLUB...
In my opinion, unfortunately, you need at least 1/2 and 3/8 and possibly also 1/4". The 1/2" size does the stuff from 15 to 150 ft-lbs, the 3/8" covers 1 to...
... The logical uh extension of this is that you can't even tighten bolts beyond a certain length, because they will break before they receive any torque at...
Mark, as Frank said, you may want a range of them, depending on what you're working on. It's kind of ironic, because as I've gotten older and my tool...
Thanks Joe, you got me curious now - just checked my two NOS ones again, and not a hint of paint anywhere, not even in the "e". The "mouth" there isn't...
I'm just the opposite. The older I get the more my compulsive obsessive impulses kick in and at this point I pull out the torque wrench for probably nearly...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
