I have a 61 Econoline pickup with the older 170 engine. I bought a Borg Warner t-85 overdrive trannie with the short tailshaft. I was planning on putting this...
What is the trans out of ? Also, There a guy that sells a adapter plate to bolt on the 170 to a T5 which is probably the same bolt pattern. I just cant...
i believe the t85 i got will bolt to the three speed bellhousing. ... From: ldj1002 To: Econosrus@yahoogroups.com Sent: Friday, February 01, 2008 10:03 AM ...
Yes, it will bolt to the bellhousing as far as bolt pattern. Everything else is wrong and will have to trade out too many parts and make adapters. Input shaft...
Terry, just checked - the left side strip I have is for a Supervan. I suppose it could be cut down for a pickup or short van if you carefully finished the...
i love mine. ... From: J B Long To: econosrus@yahoogroups.com Sent: Saturday, February 02, 2008 11:11 PM Subject: [Econosrus] Relisted Locking Gas Caps (Again)...
Well, its been a nice run, but i think its time. This is a 1963 E100 heavy duty Econoline. Straight six, three on the tree. Doors and glass on the rear and on...
Seller ended auction early with 2 caps remaining? Whats up with that? I was just about to order one. Oh well. David in Huntsville ... Merc-Plymouth- ...
Michael, Where is the van located and how much are you asking for it? You can contact me at the following email address. tunergarage@... Send me some...
I've done my searches and this one seems to be beat up a bit, with some conflicting information, and some parts that aren't available anymore... It seems that...
John, I think I can help on this one. First, the Ford parts catalog shows three sets of numbers for the '65-67 240 Econolines. Probably minor revisions each...
Bob, those are the same as 1963-65 Falcon or 1965-66 Mustang with a 170 or 200. They have a single, angled stud and also fit the '64 models with an automatic....
I just got some rather complete info, from the Falcon folks, on how to mount a 4 cyl T5 using the 2.77 bell and 8 1/2" stepped flywheel. The crashbox bell is...
no way to shift it. ... From: jimarlie To: Econosrus@yahoogroups.com Sent: Monday, February 04, 2008 8:10 PM Subject: [Econosrus] 4 cyl T5 I just got some...
Hi Guys, Does anyone have a couple of dome light assemblies in pretty good condition? I'm especially interested in the light socket and housing part as I can...
a t5 has the shifter built into the top.you would need a backseat driver to shift it.as far as i know noone makes a cable remote shifter for it.i actually have...
i need one too. nc richard ... From: Tom Walker To: Econosrus@yahoogroups.com Sent: Tuesday, February 05, 2008 12:47 PM Subject: [Econosrus] Dome Light...
Jim - Will in Whittier CA worked out the shift linkage. Below is part of a message (2006?) from Will. Gil in CT "That's me!! I have the shifter done. I'm...
Tom, is it safe to assume you want them for a pickup? If so, it may widen your search to know the same assembly was used on the 1960 (only) Falcon and Comet...
is the pickup light bracket different than the van? ... From: polecat1010 To: Econosrus@yahoogroups.com Sent: Tuesday, February 05, 2008 10:31 PM Subject:...
The pickups used a small, oval socket with a rectangular (trapezoidal, actually) lens and bezel. The vans used a round lens and bezel with either a small...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
