Gents, I used Rust Bullet last summer with good results. It requires 2 coats like the directions say. It soaks into flaky rust given enough liquid but be sure...
Hey Ron, wire brush the metal and paint with Rustoleum do not waste your money, POR15 is time sensitive so once the can is opened it will start to harden. ...
In Econosrus@yahoogroups.com, "Jim G" wrote: Hey Ron, wire brush the metal and paint with Rustoleum do not waste your money, POR15 is time sensitive so once...
Its been awhile since I have posted...dont hate me. I have gotten caught up on other projects. I feel like a schmuck for asking for help when I havent been...
i had to take a waterhose and flush out the gas tank vent tube on my 62 because i couldn't fill up the tank more than half way.if your vents blocked and your...
Good thought I will see if it runs without a cap.... ... my 62 because i couldn't fill up the tank more than half way.if your vents blocked and your caps...
Jay, I sent an email to Doug but he must have already left for Carlisle. I'll let you know next week if I need your cable or not. Tim, If I don't get the cable...
Ron, I haven't used Rust Bullet, but I've used several quarts of POR15 in the last few years. I've had good results with it. The reason they advise putting...
UPdate....I put a fuel gauge on after the filter before the carb...5 lbs...at all ranges of rpm...so this rules out the fuel pump. No need to change to an...
Could it be a timing problem? Perhaps the timing's not advancing properly? Maybe the plate that the points mount on is hanging or there is an intermittant...
Howza Guys- Here is my thoughts on this. Oh and living paycheck to paychek, i cannot drop it and get it rebuilt like I would like to. I lost the rear bearings...
I would also put wax paper directly on top of the paint, I do believe it is overpriced and depending on where you live and what weather you drive in I would...
hey all, Looking for a crashbox trans slip yoke for a fellow Econoline nut here in town. All I have are later big yokes. Anyone? Thanks in advance. Brian in...
Erick, as you already found out, idle problems are almost never fuel pump related. Is your Holley the original 1904 model, or the later model 1940 replacement?...
Spooky, if you have the time and not the money, try putting the old one back in. Nothing to lose except a few quarts of fluid. And it gets easier after the...
Craig, if you go to the Links section of the group, then to Parts Supplier Links you'll find a source for the AuVeCo seal that many of us are using. You may...
Bob, the Zenon stuff on ebay is kid's stuff. If you want a real pair of headlamps, rather than a "lookitme" set, find yourself some H4 headlamps by one of the...
for what its worth... Por15 has worked wel for me and it hasnt hardened in the can after two months of having been opened...I did thte plactic wrap thing and...
Gee, And I thought you were rotating the gears to keep them wet with gear lube. Keep up the three speed curls. Who needs a gym? Duane in Tennessee. polecat1010...
i have one from a 62 econoline. nc richard ... From: cochrane_24 To: Econosrus@yahoogroups.com Sent: Saturday, June 02, 2007 1:32 AM Subject: [Econosrus] trans...
Eddie, It might be a timing issue. I was thinking it jumped a tooth, but if so i dont think it would run at all. I havent checked for vaccum leaks but it...
Good info Jay. Just what I was looking for. I was looking at the ebay units and wondered if they were any good. Bob NCWA ... pair ... Cibie, ... don't ... ...
Sorry, Bob, looks like they're in the process of updating their site. Here's the home page; you can navigate from there: http://www.thecliplink.com/ Jay in CA...
It will run if it jumped a tooth or two, but that affects one RPM range at the expense of another. It will idle but not rev up, or vice versa. A timing light...
I've tried probably 50 different pairs of H4 lamps over the years, so if you've got any specific questions I can probably answer them. Jay (glad there isn't a...