Perhaps we should develop a support group for the partners of those with Econo addictions (an we could thereby be get away with more). Ecanonymous? ...
Looks like I have 1 for sure. What is your address? Brian Joe Horwath <joholife@...> wrote: Mine rusted out and the motor dropped down, I put a chain...
wanted: left front door glass and hardware for 63' econoline van. or does anyone know a good place to sniff around? Seattle area is best. thanks, getz ...
... under it to hold it up for now. ... check and see if I have the other one. You can have it just pay for shipping. ... crossmember for a ... is ... rates....
Ok thanks, let see what I can come up with and I will get back to you. Thanks again Fred Carello <fredcarello@...> wrote: Joe, I may have a driver's...
Getz, I have quite the collection of doors going now (acquiring two more sets today with the truck I'm getting), so come on over and we'll get you what you...
I've lost interest in this one, I'm going to focus my energy on the 65. It's mostly complete. I can get the middle bench seat, just need to drive up to...
Eric, why did you spit out a plug damn must have hurt, they are supposed to go into the engine not eat. Well looks like heli coil time or or or high temp...
If I hadn't been bleeding from my econo for the last 6 weeks, I'd very happy to take that one off your hands as my backup van. Keep me in mind if nobody shows...
Eric, If you can find an early Bronco with a 170/200 in it it will have a cable bracket and carb that will work. The 65-67 Econoline 240 cable will fit in the...
okay... i'm going to try to send you some pics. hope it works. love reading other folks strugles and acomplishments. lets me know i'm not alone. thanks for all...
Hello, I was wondering if anyone out there would have an extra inner door handle assembly for the drivers side door for my pickup. The handle is now loose and...
The bracket Fred mentioned is a great way to do the cable conversion, using factory parts. There's a scan showing this piece under Photos, Tech Stuff, photo...
Jay, Ford always has a way of complicating things! My 65 pickup has been down since June because I can't find the correct pulleys for the water pump and...
Been reading and looking at the files, postings and photos. It's encouraging!!! Looking for some bench seats for this 65. Have two children an inlaws to...
Hi, Boys and Girls. I apologize for this, but I am going to have to put off doing the article on compression for a bit. I'm very busy working on a product ...
Thanks Lee. I'm already enjoying showing off a little bit of my Econosrus knowledge around the shop where they're rebuilding my head (for free)(thanks ...
hey david thanks for responding. I will find out if ups ground can ship it. i will let you know. if you can give me the dimensions and the approximate weight. ...
Hey all, been a while since I posted, as my van has been on the road w/o problems (for now). I wanted to offer a discount to anyone who might want to purchase...
I don't have a pic, but I could send you a rough drawing of the shape should you want the seat. email me at dmix48@... for the details you requested.......
Fred, it does sometimes seem like Ford was playing games with things, but if you mess with them long enough it starts to make sense; well mostly anyhow. ;-) I...
Dominick, there are a couple pictures of the rear seat hardware in the Photos section; Tech Stuff folder; fifth and sixth photos. Let's see if these links will...
Jay, It didn't overheat but once you drove over 70 MPH the temp would increase with speed. I'm always in a hurry so 70 MPH seemed a bit slow. My truck with...
I know some group members have newer Econolines also so I would like to pass on some information. I was helping a freind move some parts this weekend and found...
Has anyone heard what happened with these RAYBESTOS MK512 Master Cylinder Kits? I purchased one from the Rockauto ebay auction and just received it this...