Sorry been out of the loop for awhile due to health and family problems, but I wanted to wish you all a "Happy 4th of July Holiday 2006" take care and...
Jim in Richmond, if you're still reading the posts, what kind of spot weld cutter did you use? Did you use any lubricant? I tried one from Eastwood and it...
Will here, I joined the CNG group (compressed natural gas) Look at what they are paying for gas. I have a friend who has a ford f150 that runs on both cng and...
Will, Any idea of what's needed and the approx. cost for converting a small six to dual use? If the cost isn't prohibitive this may be the way to go. Jim in...
Occasionally I see a CNG carb setup on ebay, BUT, they are usually 4 bbl setups. It's a very simple carb. Usually CNG setups have quite a bit less power. ...
Every TV show and almost all posts are for spending money to fix something. Not all of us can afford crate motors and mega-buck shiny parts, so this is my...
a few years ago I looked into propane conversion. It was about 600.00 to change it over.I haven't found out much about converting one of our econo's to CNG ...
Heres a nother one. I live in the Buffalo/Western New York area and WILL be buying a CNG vehicle and have the intention of putting in a fueling station at my ...
I can add to what Will's saying on CNG, upside; the CNG as a fuel is already atomized as it enters the intake, no puddling like gasoline (and no worry...
Eric, 120 pounds won't drop the front much. Mine drops maybe 1/2 inch when I sit my 200 pound butt in the driver's seat. I'm comfortable with 1 to 1-1/2 inches...
Dennis, my fault for the pics not being posted yet! I was supposed to do it, but been kinda busy as of late. Thanks for the nudge. :-) I'm in the same ballpark...
Awww shucks, Mark, you know I'm only in it for the money. ;-) Seriously, thank you for the kind words. In fact I would have quit a while ago if Marye hadn't...
Is there any difference between 65,66 and 67 front axles? I have a tight 66 axle that I want to put in my 65 then rebuild the 65 axle and put it in the 67. ...
I am looking into putting air ride suspension on at least the front end of my van for now. I am going to remove 3 leaves out of the front springs, leaving the...
The axles are all the same.Spindles different I think 64-67 all the same. Jerry in MO. MantecaJim <econowannobee@...> wrote: Is there any difference...
Need some help. I was checkin out the az trader and found a 62 van for sale. http://adcache.collectorcartraderonline.com/10/8/3/84759983.htm Hopefully that...
Jim, '64-67 spindles and kingpins are all the same. '61-63 are different, but the axles are the same. Difference is in the seal design and the ends of the...
Cool, thanks Jay, I'll be able to do my 66 to 65 to 67 to 67 swaps. I'm going to be banging on a lot of kingpins. Got the 65 running today but only so I...
Three weeks till the get-together. Am I ready? Heck, no! For those who have been here before, you know there will be plenty of good food and lots of...
Erick, I can't speak for anyone else, but I always know within the first 30 seconds of seeing a vehicle whether I'm going to buy it or not. If it speaks to...
I was mounting the rear drivers door on my van and one of the bottom bolts started ok, then got a little tight, so I started to back it out, and the insert...
Eric . Watch ( all of this stuff ) the left brake line thats bolted to the frame so the steering won't rip it off . Bottom rad hose hitting . The bump inside...
I know Dan Bishop in Fort Worth was looking for a good pickup body. This may be the one! Dan, shoot me an email and I’ll give you a name, number and...
Thanks for those tips Herb, I'll definetely be cautious. It's not as low as the one in the picture though you sent though. There is still a small gap between...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
