Well, I searched Yahoo Groups to see if there was one for EML and sure enough. Then I come here and find the same old smiling faces! Anyhow, Claude installed...
Here in the frozen tundra the damper gets very stiff on mine too. I have not found any adjustment and have been tempted to try a VW Bus one likeI had on my old...
Hi all, Here's a few pictures of the brake calliper on my EML side-car. I was wondering if any of you out there could identify the brake - I am guessing it is...
just a note.....due to a mixup, I inadvertently ordered TWO each 16 mm Magura master cylinders. These are used by EML on the K bikes, and also EZS on the K...
Sorry, I am a Guzzi guy so the MC don't apply, but the Light subject does. Does anyone know any contacts in the EU that might look up these light parts for us....
... Simon, About two months ago I bought rig with an early EML car on it that had a seized caliper with worn pads. It was the same caliper showing on your...
1982 Honda Aspencade with a Double -Wide Family Tour "GT EML sidecar. It painted a teal blue, automotive wheels all around (brand new tires last year) 7...
After some communication with Marvin, the owner of EuroWing and the agent for the new line of EML sidecars in the US, I have a better understanding of his...
I want to add brakes to my car. Has anyone found parts that will fit the application? something like a .....KDX 125... There should be something sold in the...
I had a 1980 R100S powered EMLGTII. This was the early GTII with the flat, sloped front and a 12" sidecar wheel. I replaced the sidecar brake caliper with one...
I guess that would depend on the wheel under the chair. I'm running a Ural chair on an 85 GL1200. Jay at Dauntless Motors put a brake on the chair by ...
Also refer to my Website page on the EML GT2...extensive information on the brake, shock, etc. Robert (Bob) Fleischer, aka Snowbum; South Lake Tahoe, CA, USA. ...
If I read correctly, you have the 12" sidecar wheel. Is that right? If so, I'd start by looking for a scooter wheel with a brake disk and then think about a...
I am servicing my leading link shocks. The part number is 7610-1283 Special D 506. They do not leak but the is a soft spot in the travel. Questions: 1. Should...
I have two adjustment points on my leading link fork. Can anyone tell me the performance effects available changing the settings? 1. Adjustment 1. Two bolt...
I am pondering the effects of a rear sway bar for better cornering. My rig is a EML GT (old style car) mounted on a 1984 Gold wing with rear air shocks and...
Ken, First, your shocks are Koni units and Koni is out of the motorcycle shock biz. Fortunately, they have been replaced by Ikon. Ikon makes most of the old...
Kenneth, You need to find some sidecarists to be around. A lot of this stuff will just rub off on you ;^). The two bolt positions on your fork allow for...
Since the topic of front ends has come up....... It has been many months since I posted this question so I will post it again. My EML front end has a...
To answer my own question. 1.No leaks = no new seals 2. I drained and cleaned the shock internals. No damage found. The oil had black sediments in the bottom. ...
Ken: You were given some advice to use the "front position" for decreased trail, easier steering, etc. That may be wrong, depending on how the front end is...
That "front position" business probably came from me. It is certainly possible that there is a configuration where that bolt position does not move the axle...
Last night on Craigslist Seattle under motorcycles/sidecar showed an earlier wing with an EML Setup/Forks/Wheels/GT Chair I think-running-$4000-hope someone...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
