Tranny rebushed by Stan at Cycle Supermarket. Billet air cleaner assembly from Bobby Baldwin at X-Man Products installed. Crankcase breather re-routed from...
With a fresh tranny job, I filled her with Shell Rotella full synthetic 5-30, hoping to take advantage of the quick delivery of low viscosity oil to all...
I have used valvoline pure synthetic 20-50 since I picked her up almost 8 months and 5000 miles ago. I did have a small amount of valve noise, but mostly due...
I'm kind of surprised that my air scoop mod hasn't caught on. At Daytona we did some temp readings after a ride where we all rode together for a while....
Julian, have you always used premium fuel? I never had to use it on my Harleys, but it seems to be absolutely neccessary with the EH due to high operating...
Bobby Baldwin at X-Man Products told me that he had spoken with Fisher about fitting one of their dynamic balancers to our engine. I called Fisher and they...
On Frank's advice, I called George at 732-636-0816 to see what he's going to offer in the way of crank balancing. George said that if he gets enough interest,...
If anyone has installed Bobby's cams yet, please post the results: upper rpm power? bottom end power? operating temp? valve train noise? valve float? how...
yes, 92 octane and I also use a octaine booster...I cant remember the name, but it has 4 small cans in one container, It is sponsered by dale earnhardt jr. It...
yes, I talked to them on wednesday, I am going to send them my retating assy, as soon as I finish tearing her down. I have new pistons and rings already, from...
I'll probably send mine during summer. Riding season just started here! ... From: "stumpcountry" <stumpcountry@...> To: <EHimprovements@yahoogroups.com>...
I've added three photos of the ignition switch, showing the weak point- the less than 1/8" by 1/2" tab that holds the switch together and absorbs all vibration...
Dyanamic balancing kits have add on components and have been out for while. From what I heard, they don't work well, The various magazines ThunderPress,...
Frank, that's pretty much the way I feel about it. If I can do a good balance job, I'm far better off. But I'm not capable of tearing the engine down all the...
I am offering to send to anyone who is building parts for EH's, or who has the capability of simple sheet meatl work, a template for my rear cylinder air...
Don't know who the founder is, but this is an excellent way to further confuse, tear down, and disperse the EH riders. Is this the goal of the founder? We...
The goal was to have a board for those who are experimenting with their X's, focused solely on that experimentation, and avoiding territorial disputes, ...
First, I want to apologize for failing to take pictures while I modified the switch. There are five steps: 1. remove the tumbler assembly from the tubular...
I need a set of exhaust piupes to cut up. Preferably, I need pipes that are broken or cracked toward the muffler end. I'm going to build a 2-into-1 exhaust...
Jim has the cams completed. The manifold that Jim started is perfect, I will hold off on my manifold since Jim's is ready to go and we don't want to re-invent...
I'll take a set right now just to quieten the valve train! The valve train is so noisy that I can't listen to the engine and pick out REAL problems. I've...
I found a really nice teardrop-shaped handlebar-mount guage pod today while leafing through a catalog at a Hog shop. It's made by Cyclesmith. I believe it...
I went by a couple of local "paintless dent removal" places and they said they couldn't repair the dent in my fender caused by previous wrench using an impact...
brother john. Perhaps I just missed posts on how you/one converts from conventional bulbs to LEDs on this bike? Care to share your tips on how to locate LED...
I got the red LED replacements for the rear at Discount Auto Parts for $7.95. The clears 1157 replacements for the front are REALLY expensive - about $20 each...
