I don't understand how this works can someone explain how you crush a BOV to handle more PSI? I came across this summary on EBAY and was wondering how it ...
Right on, the $90 bid I saw it's up to is more than a new one from Mitsu, not really a bargain. But, if you're interested in crushin a 1G BOV, take a look at...
I have done this many of time and have my own done this way. You simply, literally crush the BOV. Now you cant do it too far though. I have no complaints about...
I just picked up a clean one out of junk yard for only $5. New ones are badly priced though. ... ===== Justin Harris '91 Eclipse GST 'Will become RWD. Does...
I mean are not badly priced, cheaper than that for sure. ... ===== Justin Harris '91 Eclipse GST 'Will become RWD. Does that make it a GSR?' '86 Colt E Type...
Wondering if anyone has tried the Dejon Tool BOV leak stopper kit? http://users.erinet.com/40666/DSM-Misc.htm Their tests show it seals leaks even better than...
<<[b].....Basically the theroy of an intercooler sprayer is sound, regardle= ss of wether the spray evaporates before, after, or not at all. There is more...
By injecting directly into the ports, will there be enough time for the water to evaporate and actually cool the air, or will you just be water soaking your...
Just wrap it in a cloth, put it in a vise and squeeze a turn or 2. I'm selling one on ThePartsTrader for $45 and it's in perfect condition if anyone's...
I'm locating my tank in my spare wheel well in the back. Does it matter what type hose I use to transport the water to the front? I was thinking about using...
If this is merely a supply hose from tank to pump, it doesn't have to be anything fancy, even low-pressure PVC should be fine; reinforced PVC if you're...
Some 1/4" copper line (like used to run water to your refrigerators icemaker) will work fine at holding pressure in the line, and is of smaller diameter than...
... I posted this to the phantom knock digest a little while ago, as it's my understanding of the water injection cooling process. Essentially there are 2...
My stocker holds 21 psi fine, or so I think. I haven't tried any higher with my stock intercooler, pump gas and water injection. BTW, thank you all! That...
Alright I know its not injection and its not a DSM. Anyways a buddy of mine had an IC Sprayer hooked up to his WRX. He used an old rear windshield washer...
There isn't any pressure to overcome from the tank to the pump unless you are presurizing your tank. Nylon 12 is the best material to use for the tubing...
What range of O2's are you guys running WI getting. I know YMMV. But I want to get a ballpark. .94V worked best for me before, but I figure now it is safer...
Where did the water spill? I would guess you could put in a heated garage, disconnect the battery, clean up the water, and make sure the electronics are...
You might try getting some alcohol at the hardware store and mixing it with the water. Anyone know how to figure out how much alc. to add to water to keep it ...
Here's a post Grant sent me containing a cuppla great links for hose/fittings. I personally prefer hose, but .... tubing for this project would be soooo much...
Just run straight windshield washer fluid from now on. Won't hurt a thing... (and won't freeze) ... John G. Gauthier www.darklightning.com [Non-text portions...
You can physically place the pressure switch wherever you want, really. Mine is on top of the battery, held down by the battery bolt. You talking where to tap...
I rear mounted my pump and just used 4mm Aquamist line to get to the front of the car... Anything else is a waste of weight & time to engineer it. ... John G....
This automatic 'reply to poster' thing is getting on my nerves. Every one of the previous posts of mine I had to resend to the group. ... John G. Gauthier ...
Ken, You have been talking about this for a long time. Why don't you just do it and get some results. 1) unless your intercooler is stock your not going to be...
Crushed 1G BOV's should hold 22-24psi. Greedy will hold more. XSengineering is another good choise. You can just cut the flange and weld a new one if you...
I would use windshield washer fluid for your intercooler sprayer. Or you can just mix 50/50 IPA (Isopropal alchohol) and water. Rubbing alchol will work too...
Any ideas on what to use for a non IC sprayer - ie water injection system - or rather how much deanatured alcohol to run to get the freezing point down to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
