This is the monthly reminder for the DSM_water_injection list on Yahoo Groups. To send a message to members of this group, email to:...
DSM_water_injection@y...
Dec 1, 2004 10:07 am
3018
Hey guys, just wondered how many of you are using the FIA2 to accurately proportion the amount of injected water to injector duty cycle. If any of you have...
I'm not positive that WI is the reason for it, but after taking apart my type-s yesterday, the springs are rusted up good. I've been running WI for over a...
I could be mistaken, but isn't the spring on those BOVs not in contact at all with the air in the intake tract, even when it gets blown off??? I know on my ...
I wish I knew that the HKS's were like that, you are lucky I suppose. Here are some pictures (that aren't mine) but it will give you a good idea of what I am...
This is the monthly reminder for the DSM_water_injection list on Yahoo Groups. To send a message to members of this group, email to:...
DSM_water_injection@y...
Jan 1, 2005 10:50 am
3023
I need some info here guys. I'm currently running a WI system with a SurFlow pump running 95 psi of pressure and McMaster car nozzles (1.9 gph and 3.2 gph @...
Heh, I finally got around to reading Maximum Boost (Corky Bell). The man seems to have a deep-seated loathing of water injection. Did he lose an engine to a...
Those are my thoughts too. He says more or less that you won't gain any power when a car is set up correctly if you add water injection. That's complete B.S....
I think he doesn't believe that there are reliable ways to do water injection. I remember him saying something about having your engine depend on an...
I have the kit installed it was really meant for supras It has a progressive controller with a wire they say to clip to injector #1 to pulse the pump as IPW...
Injectors are usually hot with the ECU switching the ground. The question is, does the supra have high impedance injectors (or low impedance with resistor...
This is the monthly reminder for the DSM_water_injection list on Yahoo Groups. To send a message to members of this group, email to:...
DSM_water_injection@y...
Feb 1, 2005 11:50 am
3030
I've finally decided to part with my baby. I'm in Hampton, VA car can be transported anywhere by many different services or amtrack even. Its on ebay #...
spazzychalk @hotmail....
spazzychalk@...
Feb 16, 2005 3:27 pm
3031
This is the monthly reminder for the DSM_water_injection list on Yahoo Groups. To send a message to members of this group, email to:...
DSM_water_injection@y...
Mar 1, 2005 12:34 pm
3032
I searched and the link to Brad's description on how to disassemble an aquamist jet is no longer valid. Can someone tell me how to take the jet apart after...
... jet apart after unscrewing the two end pieces so I can clean the calcium out of it?<< Sure.. its easy. The top of the nozzle, with the tiny hose barb on...
The best way I found to do it was to insert a tiny drill bit or needle into the hole from the front of the injector and tap it out. Be careful to use a...
This is the monthly reminder for the DSM_water_injection list on Yahoo Groups. To send a message to members of this group, email to:...
DSM_water_injection@y...
Apr 1, 2005 12:37 pm
3036
I keep looking at the kits offered by "Acuatune" and others, they do not provide an acurate mixture. How do you get the same mix from 2,000-6,000 with a...
Look into the Derek Devises Meth injection kit. http://www.derekdevises.com. His progressive kit is pulse width controlled off the injector circuit. Jay ... ...
Dead link. ... From: Jay White [mailto:poorboyj@...] Sent: Monday, April 11, 2005 7:01 PM To: DSM_water_injection@yahoogroups.com Subject: Re: [DSM_WI]...
While you can base your injection volume off of RPM, this is not necessarily desirable. As RPM increases, the total time of the combustion is propertionally...
... with a simple pump & nozzle system, and letting the % drop as RPM increases.<< This confuses me. If i understand you, you are saying that you should be...
Paul, Yup, they do increase flow with RPM, which I contend is not usually desirable. I'm no expert, but the "internet wisdom" I have seen for years is that you...
Adrian, ... you are most likely to experience detonation in the low to mid RPM range<< General 'wisdom' from aquamist is that you are most likely to experience...
Paul, here's my take on this... The maximum amount of water injected should correspond with the rpm band where detonation most frequently occurs. That is...
Guess I didn't make myself clear on the earlier post. I want to inject 5% water to 95% fuel at ALL times except a cold engine and while ideling. I'm looking...
First of all, the torque peak is usually low to mid rpm, so what Aquamist and "internet wisdom" has to say is in this case basically the same thing. I realize...
Are you fucking kidding me... steam boost? Look, if you want a steam powered car, go buy/build one. There's a reason they stopped selling them 80 years ago,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
