Here is my site with my setup. http://www.lokmeup.netfirms.com/WaterInjection.htm Ron On Thu, 01 Apr 2004 01:58:06 -0000 "jason" <jd1828af@...> writes: ...
I am trying to find out if some one has found the water limit for DSM's. So, far the largest setup I have read about is a combination of a .6mm & .7mm nozzle....
I have the Aquamist setup, and contrary to popular belief, the system works fine with the pump and relay mounted in the trunk beneath the spare tire. I don't...
Ron, I run a .6 + a .7mm nozzle with a 100 PSI ShurFlo pump. According to my math, this should provide approximately the same flow as a single .9mm with the...
Nice writeup. For future reference, you can get a cheap $2.90 check valve for the 4mm hose at mcmaster-carr: www.Mcmaster.com Search for part number 7757K41...
First, is it me, or has traffic fallen Way Off on this digest? I receive the digest version, and I used to receive, daily, digest containing maybe a dozen...
This is the monthly reminder for the DSM_water_injection list on Yahoo Groups. To send a message to members of this group, email to:...
DSM_water_injection@y...
Apr 2, 2004 12:12 am
2739
I mounted my aquamist pump on the center subframe, just before it meets the cross-member. It took a couple very small drilled holes, and I mounted it so that...
... injection is triggered. Ive moved the trigger point around, and its just not possible for me to detect any change in afr, even with my 45% meth mixture. I...
The instructions that came with the ShurFlo accumulator suggest that you not leave it pumped up and empty for long periods, because this will cause the bladder...
Rich, Great answer below.. Thanks for doing the math.. Makes perfect sense now. Paul Elliott ... '99 White M3; < 60K miles; Dinan SC kit with 6" RMS crank...
Would running alcohol injection have an enrichening effect? ... From: Paul Elliott To: RCM1061@... Cc: DSM_water_injection@yahoogroups.com Sent: Saturday,...
I'm trying to hook up an LED to indicate when the solenoid (ground-switched by a Hobbs switch) turns on, so I have my LED anode (+ side) connected to IGN12V,...
i think your setup is wired correctly, so my guess is that you fried the LED with the 12V. if you haven't already, wire a resistor (680 ohms should work) to...
Thanks. I actually forgot to mention that I did have a 600ish-ohm resistor in series with the LED. In fact, since I suspected that there's some kind of...
Im just curious, how much water flow would you think would be a good amount for this setup. Its a '99 bmw M3 with a 3.2l inline 6 cylinder engine. Static...
Work from the smallest nozzle up to the largest your car can run. When your car starts to misfire, you have reached your limit, go down one nozzle size. You...
I have an aquamist as well, and I believe you wired your LED incorrectly. If you look at aquamist instruction, you need to wire: - LED anode (+) to the...
... Correction, what I meant is that when the gray wire is grounded, the pump is off. The Hobbs switch ( at least the one from Aquamist ) is a normally closed...
I just have a general question/comment. Why would you want your WI to come so low? (~3 psi?) I would think that your gains with WI are not evident until you...
Thanks for the info. Since I don't have an aquamist system, perhaps your suggestions won't apply. (The Hobbs switch that I bought from Brad @ Georges Imports...
It wasn't actually my intention to set the turn-on point so low. :P Since then I've re-adjusted the Hobbs switch to turn on the solenoid at ~10psi. I live in...
Wouldn't it be best to have a low start, and retune the ignition? Tommy I just have a general question/comment. Why would you want your WI to come so low? (~3...
Ok well that definitely makes more sense. That is essentially how I set my system to turn on. The bottom line is why have the system come on at times less than...
I'm not sure I understand your question... A low start? for the WI to come on? what's the purpose. my understanding of WI is to have it come on to reduce knock...
The purpose would be to lett you run less boost retard at low and medium boost. Tommy -- I'm not sure I understand your question... A low start? for the WI to...
... I can answer this, from my perspective, anyway. Unlike you guys, Im running a Vortech supercharged '99 bmw M3, making only 11 psi peak boost, and cooled...
I guess one of the drawbacks of a "simple" system (unlike one that meters water flow in response to "load") is that more than the ideal amount of water...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
