This is the monthly reminder for the DSM_water_injection list on Yahoo Groups. To send a message to members of this group, email to:...
DSM_water_injection@y...
Dec 1, 2003 6:50 pm
2500
is there a chart, or does anyone know what percentage of alcohol to add to the water to prevent freezing? all i need is probably down to 0 deg F. heck, if it...
Check out this FAQ: http://cybrina.mine.nu/water/FAQ.htm At the bottom is a table - looks like you would need at 24% mixture to get down to 0 degrees F. I...
I'm new here and going to build my own water injection on a Chevy 2.8 non turbo. I'm just looking to cool the fire a little to run A/C and tow a trailer in the...
I'm new here and going to build my own water injection on a Chevy 2.8 non turbo. I'm just looking to cool the fire a little to run A/C and tow a trailer in the...
I'm new here and going to build my own water injection on a Chevy 2.8 non turbo. I'm just looking to cool the fire a little to run A/C and tow a trailer in the...
I had an exact setup as you mentioned, but am selling it all for $250. Let me know if you want it, the parts have barely been used: 1- Aquamist High speed...
My first water injection system was on my old 89 Pontiac Sunbird GT Turbo. It was a system that I made from junk yard parts and it cost me about $100 total. ...
I just got a Surflo accumulator and was wondering if it matters where it is placed in the line? Closer to the jet closer to the pump etc. Chris Rogers ...
I just got a Shurflo accumulator and was wondering if it matters where it is placed in the line? Closer to the jet closer to the pump etc. Chris Rogers ...
... where it ... I mounted mine with the pump and resevoir, in a battery box in the trunk. I have a solenoid and pressure switch under the hood. There's about...
Thanks for the info I if there is a 8psi pressure drop I will try and mount it in the engine bay if I have enough room. If not Ill just put it in the trunk....
I just wanted to let everyone know that I have an account with HoneyWell the manufacture of the HOBBS pressure switch. If anyone needs a switch for their water...
Any good recommendations on a bulkhead fitting to put into the bottom of my window washer bottle. I got most of my WI parts and would like to install it this...
Chris, I'll take one. Send my your e-mail address for paypal. Michael ... href="http://www.H20injection.com">http://www.H20inject ion.com</a><BR> ... ...
I used a typical brass 1/8" npt bulkhead 90 deg. compression type fitting for 1/4" nylon tubing I used clear silicone sealant to help seal the fitting. The...
I am not sure of a couple of things. Like is this a 1G or 2G and what you are using the fitting for. If it is a 1G and you are trying to get water from the...
Update: I tried this method of removing the center portion, but it didn't work, so I tried to "wiggle" the center piece out, but ended up breaking the nipple...
Ah yes, i have a GVR4. Anyway I decided against the tapping of the bottom of the bottle. I just drilled a small hole in the top cap and inserted the hose down...
... Here in the states, Ive done some research on this on one of my boards, bimmerforums.com, in the forced induction section. Anyway, folks have determined...
I would like to be unsubscribed from these message boards. Thank you. Kevin Philippians 4:13 _________________________________________________________________...
kevin Vlaardingerbroek
forcedinductiontalon@...
Dec 15, 2003 6:19 pm
2525
or unsubscribe yourself from the same place you subscribed.......... OR DSM_waster_injection_unsubscribe@yahoogroups.com ... From: kevin Vlaardingerbroek...
i dont think it's the glycol. i think it's the water. if they dont use distilled water, depending on where the water is put in, it could have all kinds of...
So then just dip your nozzle in some CLR, no disassembly required :) In fact, I wonder how well CLR would work to cool the injection charge. -Martin ... From:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
