This is the monthly reminder for the DSM_water_injection list on Yahoo Groups. To send a message to members of this group, email to:...
DSM_water_injection@y...
Sep 1, 2003 4:28 pm
2284
The Aquamist pump does not show an 'open' pump flow rate. However, with no nozzle, and just using the 4mm hose attached to the output side of the pump, flow...
I'm putting together a water injection system and was doing some bench tests with a nozzle rated at 9.49 Gph @ 40 Psi. Using a shurflo 100psi pump with no...
Peter, ... cycle rate dropped to about once per second. The pulsing from the nozzle was still noticeable, but a lot less.<< What is a water hammer, and how...
... system? ... the ... It's a small cylinder with a spring loaded piston inside which dampens down vibrations (usually cause by pressure surges) in household ...
Peter, ... this route in the end. I'm also interested in making some sort of pressure riser to keep the water pressure a fixed point above the intake...
Hey all So I have my W/I system basically complete in my S4. Pretty custom install if I say so myself (will provide pics if interested!).. Standard setup ...
Tory, Id love to see pics of your setup if you can. As for the malfunctioning valve, which valve is it thats not opening? Is it by any chance the solenoid...
I still have all my WI parts for sale if anyone wants the entire package: (1) 100psi ShurFlo pump (1) Aquamist 500cc water 4mm injector Lots of aquamist 4mm...
In a message dated 9/4/2003 2:27:40 AM Eastern Daylight Time, ... the current must flow threw both bost 1 and 2 the 3rd one is ground and you only need to...
In a message dated 9/4/2003 2:25:31 PM Eastern Daylight Time, ... ok wow i caint type today. let me clear this up a little place the hot wire on #1 post place...
Thanks all for your assistance. I was thrown for a loop when I gave pin 1 GND or 12v and it would push that current to Pin 2, making me think that pin2 was a...
Take a look http://forums.audiworld.com/s4/msgs/1380352.phtml I have not provided all the information on parts used but for the most part this group already...
Tory, ... things work, but so far the car feels very smooth and no spark blowout or anything else that some experience with the Aquamist system utilizing ...
Still a question to me, does methanol wear out the pump? If you go to www.derekdevies.com, he sells a alky/meth system which uses shurflo pump just like most...
... they the same thing<< Well, all methanol is alcohol, but not all alcohol is methanol :) ... pretty comfortable with tuning addition fuel<< Why? Are you...
... cooling ... relative Latent ... removing heat ... here. For my car and where I live, it's not all about the cooling, I have ability to lean out the...
I've had a Aquamist 1S system on my 1G AWD for two years now. As far as I can tell, it does nothing. I don't mean at WOT, I mean at any time. I have it hooked...
You do realize at idle the throttle plate is closed and very little water will go through the idle ports. Probably in the form of droplets now dripping into...
Ian - Sounds like you are not squirting enough water. What size is your nozzle? Have you verified your pressure in the system with a gauge? Have you also...
Yep. But I can see most of the water going in the intake. If it doesn't drip out the intake pipe, it has to make it into the combustion chamber at some point. ...
It's either the .8 or .9 Aquamist nozzle. I haven't directly measured flow, but it empties my 1L tank about every gas tank, and I don't stand on it all that...
The way I thought and read WI was supposed to work was not as a "nitrous" type boost to performance, but mostly to allow you to run higher boost and/or advance...
Rob, You're correct. WI is for knock reduction, not directly adding power. The issue I have is that I get exactly the same knock at 17 PSI with and without my...
I would try what the other people suggest, maybe a larger nozzle? You might not be getting enough water mist in there. If you're not running 91+ octane you...
Does anyone even make a nozzle larger than .9mm? Before I even got WI I remember people saying that they were running 450 HP and only using about .8mm because...
Does anyone have a solution to the problem of maintaining a constant water/fuel ratio as rpm rises? I'm still putting together a WI system, but I'm reaching...
OK for your reference I run a 0.9mm and 100PSI shurflo pump, I turn it on 5 PSI on my 20G. I never stumble. even at very light throttle and I keep it at 5...
I'm not using the aquamist nozzles, but rather the mcmaster car misting nozzles. I'm currently running the 3GPH and 10GPH nozzles on an MR2 Turbo. This comes...
What fitting to weld on the pipe to accept these nozzles? Do you use solenoids or checkvalve? ... misting ... MR2 ... acount ... inject ... better ... WI I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
