I was wondering how to get a hold of Northern Hydraulic, I'd like to upgrade the pump for my Spearco system (I haven't gotten it yet, but I want all the better...
here you go. http://www.northerntool.com/cgi-bin/ncommerce3/ProductDisplay?prrfnbr=9414& prmenbr=6970 [Non-text portions of this message have been removed]...
What would you guys look for in a water injection controller? I'm already planning on a programable boost level to switch on the solenoid. And a programmable...
I don't think you want to pulse the solenoids, as they really weren't designed for that kind of operation. If you want to control the spray, I would suggest...
On Tue, 3 Sep 2002 10:54:23 -0400 (EDT) ... I'm not sure if the solenoids that control water injection are used this way normally. However, think of the boost...
For a rad and IC sprayed I think that would work fine, since as you said the solenoid would not be switched that often. I have pondered that for track events...
What sized nozzle, and what boost level trigger point do you guys usually use? Whose pump? I use an aquamist pump, which, with a .6 mm nozzle flows 230...
I am strongly thinking about 3 solenoids. With microprocessor control 3 solenoids can create 7 different flow rates. The water will always be within 12.5% of...
Can these pumps get wet? I'm thinking about mounting mine behind my headlight so it may get wet in the occasional downpour. Also, do they have to be mounted...
A while ago I posted several questions pertaining to using water injection with race gas. I got a few responses and one very informative one. The basic...
... Josh, Check out http://www.autospeed.com/A_0574/P_1/article.html The link points to part one of a four part series of articles on IC spraying, and...
Those are some fantastic numbers Victor, especially the pump gas ones. Are you using a metal HG to take those boost pressures ? ... From: Victor Aguillon...
Stock mitsu head gasket with ARP head studs. Victor Grant Davies wrote:Those are some fantastic numbers Victor, especially the pump gas ones. Are you using a...
alright, I just finished installing my WI system last week. Right now I'm just using distilled water. Everytime I run the WI it runs fine, but after I let...
well the switch is set for 10 psi and the light comes one when it hits 10 psi and goes off when it comes back down. It only bog after using it, if I have the...
Do you have a check valve near the TB? Or is the solenoid near the TB? Maybe the water is siphoning out of the water line after the system shuts off? Do you...
Where are you getting your pressure signal? If you take the reading from the turbo side of the TB and your CBV is sticking or set to open late, then the...
... TB? ... That's what my money is on, how much line do you have between the solenoid and the nozzle? I'm also putting in a new system, and I'm trying to...
Agreeing with what others have said, my proposed WI system, largely based on one currently in use, puts a shut-off valve as close as possible to the nozzle....
The pressure sensor gets the signal from the intake manifold. There is no line between the solenoid and nozzle. here's a pic [Unable to display image] ...
alright, for some reason I wasn't able to send the pic with the mail. So you can see it at my website. http://members.aol.com/dlyon44/WI.jpg danny [Non-text...
This is a very long message, mostly for archive purposes and for those interested in advanced tuning. This message quotes and gives total credit to "Gar" at...
http://intenz.gotdns.com/~eric/cars/turbo/glossary/turbo_calc.html This was reference in that DIY_EFI list, we need to get some people on there for some...
What is the consensus for the effect of wideband readings when spraying alcohol? I am spraying 100% denatured alcohol at WOT, and it definatly causes the AFR...
While it may be impossible to accuratly gauge your afr using traditional means when water/alky is introduced, there are certain calculations you can make which...
Alright, I hooked up the pump to the ignition so it would start pumping when the key is turned. Well it did and the solenoid was not stopping it from going...
From your pic it looks like you have the same one as I do. Could be a different model tho. Is it normally closed or normally open? You should be using one that...
... There is a way to measure the change in AFR, but probably not by using the sensor. Paul used the manual calculation method, which is going to give you a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
