I am interested in selling my 1963 dodge S200 crew cab with camper. It runs but needs some minor carb work. Has 130,000 miles and was formerly owned by my...
You may want to list it right, D200 would be 2 wheel drive, W200 would be 4 wheel drive. A "S" is a school bus frame with a camper and a 4 door crew cab would ...
Jeff Clare
jeffc@...
Jan 2, 2005 11:19 pm
3917
thanks Jeff! you're right....i only checked the original operators's manual which shows 'For "S" Series'on the table of contents page but lists specs for other...
Not problem, have fun looking around at sweptline, good site with a lot of folks that know these trucks well, ... [Non-text portions of this message have been...
Jeff Clare
jeffc@...
Jan 3, 2005 1:22 am
3919
What are you asking for it? ... From: "Jeff Clare" <jeffc@...> To: <DODGETRUCKS@yahoogroups.com> Sent: Sunday, January 02, 2005 4:04 PM Subject: Re:...
Hi, We updated the free classifieds with a Dodge section. http://classifieds.powerpassion.nl/index.php?catid=80 So if you want to sell or buy cars and parts,...
Anyone have them handy? I need all three...toe, camber, caster. Haynes doesn't even begin to list them...arg Thanks Greg [Non-text portions of this message...
Hi Greg, Castor +1/2 degrees Camber +1/2 degrees Toe 1/16-1/8" (no load for castor) Judi and Bob In a message dated 1/12/2005 4:21:59 P.M. Mountain Standard...
Outstanding! Thanks - my toe is definitely screwed up...looks like 1/2" to maybe a bit over that...I'll go measure it tomorrow.. So much for Discount...
i will be getting one of these in the near future,and it will be available for sale as soon as i get it home,im only buying it for resale.at any rate,does...
Ron, any idea what year? What do you mean by a big block? Big block V8 or flathead 6? I know of a guy who has a had a few Mopar Cabovers and if you can post...
The guages on my '71 D-100 suddenly read about half of what they should. I did some research and understand that there's a current limiter in the fuel guage....
I believe it is called a Dash Voltage Regulator. That will cause what you are experiencing. ... From: RLM Sent: Monday, January 24, 2005 5:49 PM To:...
Edward Stewart
ET577@...
Jan 25, 2005 4:38 am
3931
yes i did scott,unless there was more than one Ron S....
Hi: The instrument panel voltage limiter , as it is called just plugs into the back of your cluster. Almost al Chrysler products at the time used the same one....
I'm having problems with my fuel gauge as well and I'm thinking it may be the same thing. Before I look for one, do you know if they still sale them? Steve ...
The only thing that plugs into the back of the cluster is a little device that looks like a condenser. It's plugged into the amp gauge. I'll do some testing...
Dodge trucks did not use a plug-in voltage limiter (regulator) like the cars. In the trucks (excepting HD round gauge sets) it is built into the fuel gauge. To...
jeffc
jeffc@...
Jan 26, 2005 3:12 am
3936
To check to see if you have a bad ground, run a piece of wire from the negative battery post to the gauge set, if gauges read normal then that's the problem....
jeffc
jeffc@...
Jan 26, 2005 3:15 am
3937
On my 1961 Dodge D-100 it is located right behind the gauge. ... From: "jeffc" <jeffc@...> To: <DODGETRUCKS@yahoogroups.com> Sent: Tuesday, January 25,...
That may well be right steve, however, from 62 up they were all built in for a fact. As below, the exceptions are the round gauge sets used in large trucks, ...
jeffc
jeffc@...
Jan 26, 2005 3:47 am
3939
Hey Jeffc I didn't mean that to say your wrong. I was looking for one a while back and was told that they were going to stop making the limiter and the guy had...
Steve, No problem at all, limiters are built by Standard over seas, Wells also makes limiters made in the USA, you know which one I will be choosing...... I...
jeffc
jeffc@...
Jan 26, 2005 4:20 am
3941
your fuel gauge problem maybe the wires located at the sending unit. I had a ground wire go bad and the gauge would read a lower level than full, after a fill...
I've almost given up on my fuel gauge Terry. I took the sending unit out and sent it to a man that rebuilds them. I don't have his info here right now. It...
A qiick way to test it is to dissconect the sending unitat the tank, turn the ing switch to on and note the pointer poistion in the gage. It should be eather...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
