Hi Group , I bought a truck in Arizona and will be going from So. Missouri to pick it up in January. I will be pulling my 22' car hauler out and back. Anyone...
I bought a 2001 Dodge 4x4 wrecked for my all Mopar salvage yard DODGETRUCKS@yahoogroups.com wrote:There are 3 messages in this issue. Topics in this digest: 1....
Very difficult to find now, those I believe were the last year of that size drum brakes on the front. Best bet is a large Salvage yard with some old drums or...
hey, thanks, and i heard a rumor it would be relatively easy to pull the entire anti-lock power brake system off a newer dodge such as a ram and install the...
GREG BARTON
notrabgerg@...
Jan 6, 2004 6:48 am
3608
i have a 68 id be willing to part out, lemme know what we can work out if the parts will work out for you ...
GREG BARTON
notrabgerg@...
Jan 6, 2004 6:50 am
3609
if im reading it right, your offering parts off the 2001 dodge, right? if you are, i am interrested in the entire brake system if it will fit my budget. let me...
GREG BARTON
notrabgerg@...
Jan 6, 2004 6:53 am
3610
The newer system will not be a "bolt on" to your strait axle front end, wheel bolt pattern may be the same, but nothing else and I mean nothing else is!!!! or...
jeffc
jeffc@...
Jan 6, 2004 8:09 am
3611
Hey, When I drive this motorhome on the road it makes a whining sound, like the rear end is going out, but as soon as I take my foot off the gas pedal, the...
A: Don't know if this will make it or not. None of my posts since the first one have made it so far. Is your current hub cracked or bent? If not, you should be...
A: Sounds to me like the carrier bearings are worn and allowing the ring and pinion to not mesh correctly (unless it's out of oil, which usually causes the...
Hey Jim, I belong to some other Dodge, and truck groups and they all seem to think the same as you, so that is what the problem is. This is a 1977 Tioga motor...
I recently acquired a 79 4x4 ramcharger. I got it for the motor but have little use for the rest of the truck. Typical Wisconsin rust, needs front floor pans...
I recently bought my second 1979 Transvan on a dodge chassis with the 360. Both run well, but the first one needs an exhaust system and other body work. ...
A: I'm not quite sure what I'm going to do with mine yet. Although the roof doesn't leak now, it did before over the bathroom, so that is all messed up....
Hey ! Still looking for new, or absolutely pristine turn key 340 w/ car engine mounts... Need one that absolutely done & ready to rev...anyone know where...
72 D-500, 16 ft van box, 318, 4 spd, good tires bring your radiator and drive it home, radiator is out of my pickup and needs to go back in it. power steering,...
I didn't see my post make it to the list? I've decided to sell this rig so I can pick up a '65 D500 flatdeck to use for car hauling. I have a bunch of photos...
How can i find out what type of automatic transmission my 1988 dodge b250 ram van was equipped with from the factory? I have bought this one without...
not much difference between 3 and 4 speed , 727 has a buldge on the passenger side of the tranny pan , the 904 does not have the buldge , hope this helps a...
michael benford
m.benford@...
Jan 20, 2004 1:31 pm
3623
Hey all - is there anyone out there like LMC truck that does 1970's vintage Dodges? I've been looking, off and on, for a while now, but I haven't come up with...
A: What motor? 318 could have 904, 727 or the 4 speed version thereof. Check the shifter face to see if it shows an O/D mark. How is it in Sweden? I have a 727...
I'm disassembling 2 complete 230 flathead engines. Does anyone need anything? I'm only going to keep the long block assembly so, all the externals are up for...
John, you should put this notice on the forum for 39-47 Dodge trucks, I'm sure lots of people will be interested in parts. And where are you located? URL for...
I found a bumper near a Dodge truck in a wrecking yard over in Yuma that looked like it might work for me. It was not attached to a truck so you never know for...
Roberts motor parts has a listing for the rear bumper brackets that fit the pre-55 trucks. At the pilothouse forum there is also a pic of a 48-53 rear bumper...
Thanks, I'll check those out. What I'm trying to determine though is whether or not the brackets I found are right for a 59/60 truck, Stepside. Does the part...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
