CushmanGroup Subject Header and Posting to Group This is a regular automated message from the CushmanGroup concerning postings to the web group. The members...
CushmanGroup@yahoogro...
Jun 1, 2007 2:07 pm
29416
Does anyone have a diagram of the nylon speedometer drive gear bracket where it mounts on the axle. Does it just use another 3/4 nut or are there other washers...
The arm of the speedo gear bracket goes between inner nut and the bottom of the fork leg...I would use a star washer between the thin jam nut and the bracket...
Carl, Thanks for the info on the speed O!! I have never seen a 3 speed in a model T and have never read of such. The developement of the 3 speed for the model...
Every once in a while the subject of Model A Fords comes up on the group and some of you have one. There is a very unique book titled "The Ford Model A--As...
There were no factory 3 speeds in any production Model T. However, at least one aftermarket supplier made a complete replacement transmission. It had clutch...
CushmanGroup - Uploading Files This is a regular automated message from the CushmanGroup concerning the uploading of files to the group's YahooGroups file...
CushmanGroup@yahoogro...
Jun 3, 2007 2:07 pm
29422
CushmanGroup Subject Header and Posting to Group This is a regular automated message from the CushmanGroup concerning postings to the web group. The members...
CushmanGroup@yahoogro...
Jun 3, 2007 2:07 pm
29423
CushmanGroup Mail Delivery Options This is a regular automated message from the CushmanGroup concerning the receiving of email or postings from the web...
CushmanGroup@yahoogro...
Jun 3, 2007 2:07 pm
29424
Ray, are you sure you did not see an early model A or a model T with a model A engine and transmission in it? It would be just about impossible to adapt a 3...
I have a note copied from "Henry's Wonderful Model T by Floyd Clymer or from the book "from Here to Obsbscurity" (an illustrated history)of the Model T) which...
Na, stick shift conversions for Model T's were made before the Model A was even produced. Ruckstell made a stick shift conversion as well as the 2spd rearend....
Thank you for posting those pictures. Now you really got me scratching my head. It was the floor shift and 2 pedals which caught my attention. I asked the...
Dan, What were the particulars, How was the transmission attatched,Was the magneto maintained, Clutch hookup etc? I am familiar with the ruckstell 2 speed...
Hi all. Let's welcome LARRY NELSON to Cushmangroup. Welcome aboard. You can get engine/scooter/xmission information on this site. We cover just about...
Living in Ohio, I intend to go. Never been to one before, it starts on June 11th. I am only going two days. Is it better to go early in the week or late if I...
What ever happened to Cushmannet? A while back I clicked on it and it was gone! Did they talk too much about cushman motor scooters, and bored their membership...
Tim - I'm guessing the earlybird bargains are several days before official start, then again on the last day closeouts, and the ones I attended everyone rode...
Hi gang. Let's welcome SAFARISCOOTER@ to our group. Welcome aboard. On this group, we ask and answer questions about most Cushman machines, but mainly two...
If you belong to any Yahoo Group- be aware that Yahoo is now using "Web Beacons" to track the internet navigation of every Yahoo user. It's similar to cookies,...
Thanks, my man! It seems that Yahoo has a habit of changing things on their own without informing anyone. I opted out of ALL cookies and Web Beacons. What a...
I have a 1962 Eagle that probably needs a carb rebuild. It is either sucking air from the throttle shaft, or some trash has gotten into the low speed circuit....
Which carb is it exactly? I am not sure that bushings are available for that
carb. Carpenter's has just doubled the price for his kit for the MT carbs,
and it...
The carb is an MT for an 8 hp cast iron motor. Carpenter has a shaft and bushing kit for it, but I understand that you have to have a special bushing ream to...
You use a particular size drill bit to remove the old bushing...I have used these bushings and reamed the holes about three times but its been about 7 or 8...
I am sure you can fix you carb but the best thing you can do is order you a
new 22MM Mikuni. You will get better performance and no leaks. It will start
better...
Hi Carl, I was wondering if you are on the Mikuni payroll or something. carl <csharley@...> wrote: You use a particular size drill bit to remove the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
