I have a set of old rotors that needs to be turned down. I can't find in the manual what the minimum thickness is. Does anyone know how much the rotors can be...
Some how my last message wasn't completed. Brake minimum thickness is the qustion. I also need a front brake caliper if anyone has one they would be willing...
Back than when rotors were fairly new--thickness wasn't such as we have now--no stampings on them--it's best to only turn as little as needed or to grind until...
merri, those two beauty rings you requested a price on 50.00 plusthe7.00 I spent on shipping Thanks Danny ************************************** Get a sneak...
Okay Danny - we'll be sending all of them back to you. We are poor people and can't afford the expensive chrome plating to make them useable. Merri ...
I recently swapped engines on my 51 SS and in the process of hooking the new engine up I crossed some wires on the solenoid, got some sparks. I am able to...
I have four CIBA engines and would like to rebuild one for my Super Sport. Can anyone tell from the engine numbers the year and if the cranks were steel and...
I would say unless the engines were updated during a rebuild (those marked with an R are likely to have been rebuilt) the only one that might have a cast steel...
Don, I have a set of caps from my 51 CD wagon. One has a small crack in the face but the other 3 are in good condition. Not sure what they are worth so make an...
Unless your discs are in very bad shape, leave them alone. Clean them up as well as you can with sand paper and install new pads. Then you can show your car as...
Berry..I think Don needs the Domed type. Yours should be the flatter type. If Don doesn't want them and they are the flat type as should be on a 51, I might be...
Pete, Mine may not be original to the car but they are domed. The "dish" of the cap is 2 1/2" deep. Is there a cap with a deeper dish? Barry ... From:...
Barry, I don't have my car here at home so I can't measure mine till tomorrow, but, yes. There are the earlier type that has a much deeper baby moon dish, and...
selling my '52 Hot Shot nice car, needs only gas and a charge.. 785 miles on the OD, new tires and interior, tonneau cover to match. email me directly for...
Art, If the engine has a generator it will die if you pull the battery cable, but if you keep the engine revved up it will stay running, that also it means...
I checked out the seats in our '39 and they have the plywood bottoms that attach to the seat frame, and the seat material wraps around the frame to the...
Barry, I know Croftons have the steel crank and strapped mains as well as my engine from a military generator. Did all the Fageols use the steel crank and...
Fonda and I will be leaving (again) for a few days, we will be gone from Saturday September 15 until Monday September 17 (all next week). We are trying to get...
I have a 51 Wagon, good shape, not alot of rust, some on floor, been garage stored for years, clear title, not running. I could maybe get you some pictures....
OOPS! That should have been from Saturday September 8 (this Saturday) until Monday September 17 (see I NEED the vacation). Sorry about the confusion on my...
Morning! Can anyone give me the measurements for the rod bearings on a 52 Crosley? I need the rod big-end diameter, crank diameter and bearing width. Thanks! ...
Was wondering how many weeks vacation you get--I'm told I'm Retired- yet I can't get away from home except for the OHIO show(My working vacation) Anyway (LOL)...
Are you going to put it in your Indian?..........peter ... From: indian4our To: Crosley_Gang@yahoogroups.com Sent: Wednesday, September 05, 2007 12:53 PM ...
Chuck, I intend to quit Jan. 1- 08. Going to hand it over to my son. 47 years in the foreign car repair trade is enough. How's the other side treating...
Pete,The pay sucks-went back to work-my son and 3 kids moved in for 2 weeks,16 months later they left-I'm out of room to work in-Sold 7 cars last month just to...