HELLO, I;M TRYING TO DECIDE IF I CAN PUT IN A EFI SYSTEM FOR A REASONABLE PRICE. THE WIRING HARNESS IS MY GREATEST CONCERN. I AM NOT A WIRING PERSON BY ANY...
I've been half-way following this thread, and it seems to me that the original springs and the 'lift' springs should have about the same spread from eye to...
Does anyone know a better way to remove the distributor gear? I heated it red hot and carefully drove it off with a mallet and soft punch, but it was crazy...
Roy - What a small world, huh ?! It may have been a '65 but I don't remember the black inset (could be old age -He! He!) That main drag was Santa Fe Ave. and,...
I checked my 64 comet/falcon shop manual, and it gives dimensions for leaf spring mounting holes, but not the length of the springs themshelf. The falcon ...
Let us know what you find out.... George ... From: Comet-List@yahoogroups.com [mailto:Comet-List@yahoogroups.com] On Behalf Of Howie Sent: Friday, February 01,...
We may have to change the list to Comet-List@... http://ap.google.com/article/ALeqM5jqLj1k2yPSZpOh8wXdL9ttj0vRnAD8UHM0I02 Largest bid in the industry...
Brian, if you don't have a wiring harness, get one out of the bone yard. Make sure it is the same harness that matches the computer and year of the donor car....
Does anyone know if there is a difference in the front spindles of a 6 Cylinder Comet and an 8 Cylinder for the years through 65. A tubular 'Control Arm'...
I have done several of them using the stock harness/computer/sensors out of a 89-93 mustang. Doug Minneapolis HELLO, I;M TRYING TO DECIDE IF I CAN PUT IN A...
I am parting out a 63 S-22 hardtop that I just bought. It's a V8 car, with bucket seats. Complete minus engine, hood, and console. Please let me know what you...
Hi- I'm looking for exterior trim/moulding for my 63 S-22 convertible. Anyone know where I might be able to locate some in good shape? Thanks, Lance...
When I replaced the gear on my 351 I removed the pin and used a puller to start it sliding down the shaft. Then I could slide it by hand. No heat, hammering,...
That's not enough of a difference to worry about. It's the thickness of a CD or DVD. I'll bet the tolerances for the hole locations is that much, so I wouldn't...
I went thru this when I was putting my 64 together, when I got my car it was set up for straight axle. 64 comets were a bastard yr, the steering linkage was...
spindle for 65 comet are differenent. Thw V/8 spindles are the same as 65-66 Mustangs.(C5ZZ) ... From: Howie <fecomet64@...> To:...
petescomet@...
Feb 2, 2008 2:52 pm
38331
I am in need of 64-65 Falcon - Comet 6cyl Power steering pitman arm. Looks like the shape of an L and has one hole and fits the 1 inch sector shaft....Pete ......
petescomet@...
Feb 2, 2008 2:55 pm
38332
Pete I just recently purchased one from www.greensales.com call and as about it. If not the 65 mustang uses the same one as the comet....
I looked in my parts interchange book and it has the specs. for the leaf springs. Forgot I had this book, anyway the 64 specs. are 2 1/2 wide x 22 x 33, for a ...
Hello cometeers, the Pux Ground Hog (seen?his shadow today)?in PA?, means?6 weeks of winter left . In approx. eight weeks Comet East has their first event of...
petescomet@...
Feb 2, 2008 3:24 pm
38338
Hey Pete do you go to the Ford swap meet in Columbus, Oh? I thought I seen where somebody on here goes there with parts. Not as good as it used to be, same...
Yes I am. But most chassis and suspension parts can be found at www.mustangsofchicago.com too ... From: Howie <fecomet64@...> Sent: February 02, 2008...
Sure do, this year its on the same weekend as Charlotte but comitted to Ohio. Some of us Comet East members from the deep North will be at the Swapmeet as last...
petescomet@...
Feb 2, 2008 4:52 pm
38341
Will have to do that Pete, I go every year, prob talked to you before. I live in Springfield, 40 miles west of Columbus. Howie 64 Caliente 428 A/FX Clone ...
Member of Comet East?????? ... From: Howie <fecomet64@...> To: Comet-List@yahoogroups.com Sent: Sat, 2 Feb 2008 12:05 pm Subject: Re: [Comet-List] Comet...
petescomet@...
Feb 2, 2008 5:12 pm
38343
can anyone tell me where to find a dipstick for this ford-o-matic in my 63 4 door. dearborn and the like only seem to have dipsticks for the C4. also, is...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
