Using the below described method I get a measurement of 2 inches and 3/32 of an inch. ... the same as center to center and you can get it correct enery time ...
So I got an oil leak on the right side of the scooter. After a bath with some engine cleaner I was able to determine the gasket is broken. What I think...
Well it seems to me the hole centers on the intakes vary from GY6 to GY6. So the question remains if there is a good metal intake that will take my 2" hole...
I have found it useful to visit some of the websites dedicated to ATV's and go-carts, as most of them use the 150cc GY6 engine, and they have lots of...
Just wanted to poll the masses. My Ricardo 250cc (like tank touring 250cc) original CVT belt failed after approximately 1500 km. Is this a bit premature?...
Just replaced a belt for a customer who had 6500 miles on his short transmission. The scoot was a Baron 150 cc Retro. So, it seems that 1500 km is way too...
Yes failure of the drive belt at 1500km is way to early of a failure and could point to an issue or two like: The orginal belt could have been defective. ...
Ok, my Ricardo 250 has had this chronic rear brake line leak since day one. I have replaced the hard line with no affect. I have since gone to a 2 piece...
Yes, do clean out the transmission compartment. Use a vacuum cleaner, and even a dental pick and mirror to find little pieces of the old belt that got into...
... only ... lights ... I feel your pain had the same issue this last week with my 250 Jonway. Symptoms: Only starts with remote Turn key on, gas and temp...
Putting teflon on the threads of a compression fitting is a no-no. It keeps the threads from being able to pull the fitting together tight enough to make a...
Push the "unlock" button on your remote twice. If you use the remote to start the scooter, you MUST also shut the scooter off with the remote. If you don't,...
If anyone here needs better explanations of the internal workings of their scooter, I will be glad to consult with you over the phone. I have done complete...
What do they have in common? Brake light bulbs test good. There must be a switch in one or both handbrakes to turn on the brake lights and also function as a...
Thank you for this offer. I will keep it in mind as I look into why my scooter started to run like poo! (after my mis-adjustment of the valves). L. ... ...
... me ... electricity ... If you were to look into the files listing for this group you could find a gif of the electrical wiring diagram of a typical...
Thanks, I tried that already!! It is how I got up to 50 km without loosing the brake alltogether. Any other ideas? ... day ... was ... would ... point ... ...
The fittings are 37° JIC hydraulic fittings I believe. There is no cutting or moving nuts or ferrules possible. All the fittings are crimped on. It is...
I ordered the fly wheel puller from Buggy Depot to receive it today (not an ad); fast shipping. I got the fly wheel off by backing out the center bolt on the...
You could try putting string or twine around the brake hand lever and tie it so that pressure is applied constantly , now listen for noise that would indicate...
I have a 250 Chinese scooter. The issue I am having is that when the scooter is cold it is not starting up easily. I replaced the CDI unit with a new one but...
Try starting but before it starts after several cranks stop and pull the plug , does it appear to be wet or dry? While there check the condition of the plug...
My 250cc Chinese scooter has just rolled over 3600 miles on the odometer, running like a champ.. I'm regularly cruising at 45 mph indicated with tachometer...
oops: "I was surprised to find the center nut on the fly wheel was not metric but standard; 3/4 inch socket." I meant to write I was surprised to find...
You could put the scooter on the rear stand (back wheel off the ground) and screw the idle adjust screw in about a turn and a half then try to start the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
