I am looking to add headers to my 1970 Chevelle, 350 engine. I am looking at the Summit site and wondered if anyone have any experience with the following...
I excactly just put on the Flotech but for my F150 which has a 302 (this is my winter beater / kick around vehicle) and are only 3 mos old- so I will be...
I am very happy with my Flowtechs. I have had them for 4 years. Very easy to install on my '69 Chevelle w/ a 350. Phil ... I am looking to add headers to my...
Now that you mention it, I did have to skip using the first header bolt on that side. I used the original manifold bolt and fabricated a spacer using a length...
hey all... i'm just getting over some internet problems, and i see the posts about header problems... i might have one, too... i'm putting a 350 into my '72...
Hey Georgec; Yes, this is very do-able. Not sure what motor your running, but I use a Crane equiv. ( don't recall part # offhand) of the L78 cam (396/375) in...
Comp cam 280h good one ... From: ChevellePages@yahoogroups.com [mailto:ChevellePages@yahoogroups.com] On Behalf Of G Sent: Wednesday, December 07, 2005 12:30...
Stock GM. Goes to 8500RPM. Unless you are going to do some serious racing you don't need one. Jus rebuild your stock one. G <georgec@...> wrote: any...
Is an X-pipe exhaust system really better than a straight dual exhaust? Take for example a 350 with an automatic, stock exhaust manifolfds, edelbrock performer...
Hi, I need to know if a 1964 4 door Chevelle frame is the same as a 2 door hard top. I have a 2 door with a wrecked front end and want to swap the frame for a...
I am getting ready to race my 64 Chevelle in the 1/8 mile. I have never been through the lights before but have read up on it. My question is do I go on the...
If you're racing on a full tree, 3 amber countdown lamps .5 seconds apart, you'll need to leave when you see the last amber. It'll take that last .5 seconds...
Go on yellow. In fact, push it in an attempt to go red once. You'll probably find that between reaction time and the car getting off dead-stop, you can start...
Thanks for all the input, I think the last yellow it will be. Can't wait to check the reaction time when I throw the switch to the Chevelle's big Electric...
Hi, I am new to the group and i would like some suggestions and comments on some things to be aware of in restoring a 65 ss car. I also would like to know what...
Just looking at past messages and found a link to summit racing and some Eldebroc no hop bars for GM A body's. But the description says for 65 and up model...
Has anyone heard of a cast iron distributer?I ran across one and was wanting to know what the hell this goes to!!!!I've never run across one before.There are...
The early motors used them... 265, 283 and a majority of 327's Anthony P. ... From: swinters923 To: ChevellePages@yahoogroups.com Sent: Saturday, December 31,...
1955 ------1959 small block ... From: ChevellePages@yahoogroups.com [mailto:ChevellePages@yahoogroups.com] On Behalf Of swinters923 Sent: Saturday, December...
I have a 1971 Chevelle SS. I wanted to know what offset I need to get on the Cragar SS rims for them to fit without rubbing on the wheel wells and also what is...
... You can fit 10" rims with a 5.5" backspace on your Chevelle. This should clear up to to 295/50/15 tires. I believe I've heard of some going to 305/50/15. I...
Correction on my reply. I'm running 8" Vette rally on the rear with 4" backspacing with 275/60/15s. Almost a 10" footprint. Looks and fit well. I'm running...
I just put some 10x17 Budnik Fontana Dish Wheels on the rear with a 5 3/4 back spacing and a 275x50x17 Nitto NT475, fits good. Looks good if I say so myself. I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
