Welcome ! I am sure you will enjoy being a member, Lots of good info etc Bud ronvanblarcom <ronvanblarcom@...> wrote: I just wanted to intoduce myself...
Just joined the group, & i have a question. This is my second "70" SS Chevelle,(bought the first one in 1969) While replaceing the original door panels, i...
RON. SOMETIMES YOU WOULD FIND THEM IN THE SEAT SPRINGS, ON TOP OF THE GAS TANK, AND YES, EVEN IN THE DOORS. AS FOR BEING GLUED? YOUR GUESS IS AS GOOD AS MINE!...
It was common but not standard practice at most plants. When the car was finished, the build sheet was excess paperwork and instead of putting it in the...
... SS ... original ... or ... It seemed to vary where they placed the buid sheet.I had a 68 and a 72 Chevelle and found the build sheets attached to the rear...
Hello, I'm new to this group. Could anyone send me a copy of a build sheet for a 67 chevelle? Yeah, I know you can buy one on ebay or a number of other places...
I have a 71 Chevelle SS with a 454 in it. The other day it started to kick a little bit and the next day it got pretty bad. Anytime I stopped the car would...
Probably got some dirt in the idle air bleeds. You'll need to disassemble the primary side of the carb, and blow air through the passages on the body to ...
Cameano@...
May 4, 2005 7:27 am
2406
I have the same engine and carb, and recently had a similar problem. It sounds like trash in the gas line, or in the carb, since it happened while driving, but...
If you have not tried it yet, disconnect the fuel line and see if the fuel pump is working. This is best done with two people so you done get gas everywhere. ...
Greg, You first need to determine that it is a fuel problem and not ignition. Pull a sparkplug wire off and put in an old plug and with rubber gripped pliers...
Hey Guys, I'm new to the board here and wanted to see if you guys had any thoughs on the 1964 I just bought. I've got a rolling chassie and so I'm looking for...
I have a 64 chevelle coupe and may be willing to trade some parts I have a th350, a radiator, in a couple of months I'll be taking out the front bench and a...
I recently had my 67 Conv. ran on a Dyno here at a local place for some giggles as my brother has a 69 w/383 stroker. So you know how brothers are, and after...
Does anyone have a list of part# and vehicle makes and years. I would like to convert my standard shoe brakes over to disk. Would I save money doing it that...
I have a baer brakes serious street front disk brake system for sale they are 3 months old and works great I have driven the car maybe 15 times with maybe...
Skye, I've emailed you a few times and have not herd back I was wondering if you knew what you were going to do or not? Also I'd like to buy the 12 bolt...
Hey Skye, I'm interested in them at a later date. I'm going to wait to see when the parts I got from you get here and them see where I stand on the car. so far...
I bought a conversion kit from True Connections (www.true-connections.com). They have several kit options : Standard Height w/ 10.75" Rotors $750.00 ...
Eric Senior
esenior@...
May 20, 2005 11:52 pm
2419
I found mine under the rear seat. In any case KEEP IT! Photocopy it store it like a valuable piece of paper. 70 SS chevelles are hard to document, the build...
There should be two buttons , one that says "Add Photo" and one that is "Create Album". Click on either one to upload pics from your computer. You can even...
wes still confussed as to how to insert pictures into album I created call my '68 SS 936. Wes <chevelle_454_heavy_chevy@...> wrote: There should be two...
Hey Guys, I've got a 64 with all the factory chrome for it that I'm looking to trade for some parts. I'm looking for a transmission to bolt up to a built 454...
Look at Hotrodgossip.com go to the classified section. There you can find all kind of stuff.Disreguard the background pic's there is car stuff for sale. JW ......
I would like to have a drive shaft made for the conversion from the turbo 400 to the 700r4. Does anybody know how much shorter the drive shaft will need to be?...
I believe the short shaft 400 is a direct bolt in for a 700r4. I am replacing the 350 turbo in my 70 with a 700r4. jww1_2000 <jww1_2000@...> wrote:I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
