The K-134 is also called the MULTIFUNCTION MODULE (MFM). GM part# 90494163 pictured here. http://www.rmsautoparts.com/prodimages/90494163.jpg You are seeing...
... K134 location: Remove the trim panel from below the steering wheel. Remove the black vinyl covered insert that is underneath that. With a flashlight, lay...
Call your Cadillac dealer and give your vin to check to see if there is a recall for this. I just had mine replaced for free due to the recall. Recall was for...
I was just quoted $765.00. can anyone share any similar stories??? I'm freaked out. Also the rear coil springs at $928.00. Thanks, I love my car but are those...
... Exactly what part(s) are they claiming to be replacing? The actual sway bar or the sway bar drop links? The drop links are about $17 dollars each and can...
... From: "gord_gecko" <gord_gecko@...> ... I think he was talking about the drag link, which is the main steering bar. I don't think there's any wear...
Ca va tres bien merci. :D They call it the drag link. The rear coils are approx 900.00$ wow ok. He says its the ball part that is abput to slip out of it's...
There are used rear coil springs in Canada listed on www.car-part.com beginning at $120 a pair. I agree with comments here elsewhere that failure of those...
We went and looked for prices at Rockauto.com. Rock Auto?site search engine seems to not be working correctly lately. Anyway, rear springs? Yeah right. You...
... I'd take the advice others have offered and at the very least get another opinion from a different shop. Technically, I don't even think Cat's have a "drag...
The drag link might be a nasty repair, though that price sounds a little high. Was that parts and labor? There is at least 1 ball joint in the drag link...
I am replacing my idler arm as the bushing was worn, but I cannot get the ball joint taper from the drag link to the idler arm to sepparate. I don't want to...
What about using a two or three jaw puller? Off the top of my head, I'm not sure of the sizes and clearances but I think a 2-jaw might work. ... From: rom1047...
... I'm not sure of the sizes and clearances but I think a 2-jaw might work. ... In CateraOwners@yahoogroups.com <mailto:CateraOwners@yahoogroups.com> , ... ...
That was exactly what I was thinking of! AZ does rent them but they may not have the size needed. I've had to purchase my own for some uses. ... From: Dan...
... The beauty of the second type is it will fit in places the first one won't - in particular joints where there's an obstruction close to the stud end. You...
... won't - in particular joints where there's an obstruction close to the stud end. You ever see one that works like a screw operated pliers - one jaw fits in...
Called the dealership and they said this recall expired in 2003, plus the recall was performed on my car in 2003. You have been lucky that you could get the...
Yeah...that would jive with what the campaign language said about 7 years or 100,000 miles. Odd that it would still be open, but hey, any dealer that would...
I apologize. I sent this message earlier but I must have done something wrong because I didn't see it post. This morning I noticed my LH - high and low beams...
I personally find it easier just to take out the headlight to get at the bulbs rather than move the battery and stuff. It comes out pretty easy - four screws...
what tool is needed and can I rent it? in Toronto Canada. I am changing water pump, timing belt, radiator, and serp belt. have received the parts. any comments...
You need the J-42069 tool or version of it to replace the timing belt. The kit is available as a rental. See: http://www.ledfix.com/timingbelttoolrental.html ...
I am stunned and impressed. :) I am so happy I found this group and i will never leave! yes i thought it odd too for the drag link- and it is actually...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
