Guys, some have inquired if I'm bringing Mikuni's to Mid Ohio. Yep, I will have a table of Mikuni's at Bob Fornwalts location. If you want a Mikuni at my low...
http://www.cycleworld.com/article.asp?section_id=3&article_id=771&page_number=7 Good stuff! Let's get on it! I want Super Hunky back in the saddle! ...
The 175TNT shut off today after a about a half hour ride. No spark. Has original ignition. Checked the obvious; any ideas? Also, What is the prefered method...
I guess I would start with the kill switch. Not common to have one quit while running. Second option would be the coil, since it died when hot. The good news...
I have a small MX-1/2 tank and the stud for the rubber mount wont come out of the threaded insert in the tank. Has anyone successfully fixed/replaced one of...
Brian, I had a problem with the inserts on a petcock I removed.The screws would not brake loose so the inserts spun out. I replaced them with an insert used in...
Hi Dave: Are the inserts you used kinda like T nuts with prongs that will bite into the plastic? would you hae a pic or something similar to what you used? ...
Dave, thats exactly what mine did. How did you remove the stock insert? Did you drill it out? I already have a "rivnut" tool a kit to replace the insert but I...
I asked this same question a few months ago on a tank that I had ...... the threaded insert was spinning inside the plastic..... I was going to drill 2 maybe 3...
BT, I have a TNT tank that is cracked that could possibly be fixed but I think instead I will cut it open and take some pictures of the insert and how it is...
Hi David! Your part is on the way! Thanks Remi www.comeca.ca ... From: David Chaisson To: Can-AmMotorcycles@yahoogroups.com Sent: Tuesday, July 08, 2008 11:05...
Just wanted to post a note to express my thanks to Al Roberts for his help. This guy is the real deal! What a positive, informative conversation I had with...
Hello, currently riding an MX4 370 as a practise bike. I'm going to a track in the mountains this weekend, elevation about 4000 feet, temp. about 90 degrees....
Still trying to find a good paint match for the 80-82 Qualifiers the tractor orange recommended is too yellow/orange,,,needs to be that red/orange rather than...
The SWM Orange is a bit red/orange, if you want to try it I can ups you some. It's $10 a spray can, professional grade paint.  Keith ... From: donrokon...
No, I just filled a hole in a pro grade paint for the SWM's. The CanAm's seemed to have options or at least close ones off the shelf. I had NOS parts color...
... Donald, I think the paint on the qualifiers changed in '82. the 80 and 81 models were exactly the same,and for this ,I have used Engine enamel Chevrolet...
Just finishing up my resto on a '75 TnT 175. The rear shocks are tuckered right out. What is a good (but not overly expensive) shock to replace the originals? ...
For the type of riding you are going to do 14 series Progressive shocks with the lightest springs will do. They are not up to racing, but they work well for...
I have a pair of progressives on my 74 Can-Am 175 TNT and they are what Brian says they are. I personally dislike the way Progressive presents their shocks on...
Plasti-kote Engine Enamel Chrysler orange NO.226 is a good match Dave ... From: donrokon <donrokon@...> Subject: [Can-AmMotorcycles] Paint Match To:...
Anyone looking to replace tank and fender decals for older CanAms should check out; http://www.reproductiondecals.com I just ordered a set for my TnT, the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
