... Larry, Most of the parts bikes I've seen are really far-gone so the pipes are rusted right through.You may have to cut, bang and weld your existing pipe....
Hey Larry, Am in the process of restoring a 1986 Can Am 250cc ASE & am having a problem locating NOS parts for the swing arm. Hopefully you can point me in the...
Hey Keith, We talked via telephone this past Monday. I'm to call you this (tomorrow) Saturday morning re: swingarm parts for 1986 Can Am 250cc ASE. Thanks, ...
Thanks for the comments Ron. So far, this should be a fine showroom queen. It's pretty much an unmolested barn bike that I have found just about everything to...
Guys Is anyone parting out a 1980 MX-6. After stuff such as a front wheel hub etc but anything else considered. Reference to shipping I live in the UK many...
Its a short list for now because I am halfway through totally stripping the bike ready for powdercoating. I do know at this stage that I want a front wheel hub...
The hub would be great thanks. What sort of condition is the tank in please? How much do you want for the items? Thanks again ... has a lot of stuff:...
Greetings VMX Fans, What to do tonight? Read some of the Coolest VMX Retro News and Interviews on the Planet! http://www.mccookracing.com/archives.htm Who's...
I recently found a guy thru Al Roberts that manufactures a coolfactory appearing down pipe. He makes it for the MX-2 250. Will it fit on the MX-2 175?? Or is...
The 250 pipe wont fit, the manifold is bigger. The 125 and 175 pipes have the same manifold size. Jemco makes both MX-3 up and MX-1,2 down pipes for the 250,...
Thanks Brian, do you think I could get Circle F to cut the header pipe off of my stock down pipe and weld it on to the expansion chamber of the 250 down pipe?...
Is your original pipe damaged? If its not too bad both Jemco and Circle F can copy it I think. Best thing to do is call them. I know the Circle F pipe for the...
Thanks Brian, I have inquiries to both for repair and reproduction, but have not yet recieved an answer that either would take on the project to replicate the...
Doing a full MX-6 rebuild. Just throwing my parts wanted list out to all. Can anyone help please? Swing Arm 746 100 011 Bushing x 2 746 097 004 Sleeve x 2 732...
Hey There, I'm doing the same thing but with a 1986 250cc ASE & needing most of the parts you have listed...I contacted a couple of folks but they said I was...
Hi! I have some item what you need. Please visit my web site at www.comeca.ca in search,inscribe a old Bombardier part number or a key word you will find this ...
Hi William! Thanks for the feedback! Check in my web site soon I will add a free technical and mechanical information for all can-am. Have a good day! Remi ......
I was a Can-Am dealer, back in the mid/late 70's. I have several of these small pieces NOS but not all of them. Where are you located. ? Let me know if you...
I went thru all my stuff and came up with the footpeg springs if you need them still, NOS. Also found what may be the bearing cups, NOS, but the part number...
I picked up a Can Am 75/76 Supplement to the Manual...... it has been water damaged and the last pages in the Technical section in the back have been...
... If ... Hi Brian. Have this. Will post for everyone. Apologies for the quality as mine is a copy and I was having a couple of brown pops while scanning eh!...
Hi. I recently rescued a Can-am bombadier bike from a rubbish skip and need help in identifying model,engine capacity etc.Then restoration. The bike has state...
Hi. I have an old plastic desert tank with a 1/2 inch inside diameter hole for the petcock and grommet. Plastic is about 1/8 inch thick. Does anyone know if...
