Since I never touch the adjusters on the levers, I purchased fixed non-adjustables for a Kawasaki Concours. The Parts Unlimited brand can be found for about...
I am most likely going to be forced to sell my GC to raise some cash . The bike is not cosmeticaly perfect , but is mechanically very sound and makes great...
A while back I posted a message asking for pictures of side bag mounts for my son. He was going to try and make a set of mounts for his newly purchased Gran...
My clutch went out as I was about to ride to SLC for world Superbike last week, fortunately it went out at home and I was able to ride my wife's bike:). Anyway...
I still have 2 very nice GC's for sale in Reno. $4000 and $5,000. For $5000 you get a hp kit,brand new ($350) tires, 20 miles) $500 service 500 miles...
Thanks for pointing me in the right direction. The clutch lever used in the GC is also used in a great number of Kawasaki models. It is Kawasaki part No....
If you have the slave cylinder off, you can apply air pressure through the line fitting. This will force the piston out, but please note, you must use extreme...
Yes, did that, slave looks good. The master cylinder is the one that is the problem and I don't see any way to get the piston out. The actuation rod has a boot...
I'd just pick up a new or used M/C as they are all over ebay regularly (a set for sale now with a BIN of $50usd each for clutch and brake) or pick up new items...
I have rebuilt other brands in the past that had a compression ring that was not visible either. To remove the piston, I drove it out with a rod from the line...
Hi! I got problem with front brakes: it works but lever very soft and reach handlebar when I squeeze it. I bleed it, it helped a bit ... for two weeks. Then,...
rubber or steel brake lines? how are you bleeding the system? from the top or the bottom? using a MityVac or some form of vaccuum bleeder or manually pumping...
Make sure no leaks anyplace...look at all the junctions. 1st dump most of old fluid from master reservoir, but not all This way you won't let air into the...
Thanks, but need the master. Jeff ... From: Cagiva_Gran_Canyon2@yahoogroups.com [mailto:Cagiva_Gran_Canyon2@yahoogroups.com] On Behalf Of Alan Sean Sent:...
I'm a new member to the group. I traded for my 2000 Gran Canyon Tuesday and then rode it home 180 miles. I haven't been this fired up about riding on the...
Tommy: Welcome aboard...new members are what keep this forum fresh and interesting. I know you will learn a lot about your GC here, I know I sure did. Too bad...
Tom, Like Marv mentioned, you can find quite a few of the items on eBay. A few weeks back there was an inner and rear fender for the Cagiva Navigator on eBay...
Hey Tom. Haven't I seen you on the Cousin Weedy CZ group? I had a run of tank and side cover decals reproduced. They're identical to the stockers. Call me if...
Rusty, I recognize your name. Maybe from the Maico group? I joined the Oldscool CZ but I can't remember why, never had a CZ. There's a newsletter site that...
... I got a rear fender assembly from the dealer in Varese, where the bikes were made, maybe he has another. I was unable to find one in the US. Tail light...
Tommy: Check with these guys, Moto Ricambi, who are located in Varese; they might have a lead on the parts you need. Also, their website is up, however, a lot...
if MORO can't get it then no one can you can also fax them maybe try italsport in Manchester for used parts http://www.italsport.net/ though Roy is the Elefant...
Thanks Kevin, I'm getting rebuild for slave cyl. and will try that first. Everyone tells me the master never goes bad. I'll be out of town for a week and when...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
