Sorry Steve, Hydractive 3 has moved on with the C6 & new C5 compared with the old C5 in that they have variable dampers at each wheel & height control is...
YES ,I HAVE NOW A HAYNES MANUAL AND i HAVE TO OPEN REAR WINDOW WHICH WAS STICKING AND NOW REMOVE 4 TORQ BOLTS TO GET ACCESS TO THE DIODE AND IT STATES THESE...
I had a bit of a search around various forums regarding the high level brake light & the MOT. It's a bit of a grey area, it seems that if it's connected, it...
Thanks, However I am living in France and the tester said it should operate.however You are given time to do it and do not need to return to the test station....
After reading many reports about bypassing the particulate filter. To do this ,I understand that you have to fool the computer,you have to put some kind of...
Hi All, I have this problem with my C5 2.0 HDi est (LX 03reg) Generally pootling around town or cruising on light throttle it is fine, but just recently if you...
Dear all See ads for number plate, boot liner and roof rack bits from a site called 'preloved' - they might ring someone's bell. I don't know if they're still...
Hi, If I can share my experience from attempting this fix . . . The "scotchlock(s)" are available through Ebay, and can be bought in small lots for a few...
MY 2.2HDI 2001 HAS HAD A LOSS OF POWER EARLIER THIS YEAR WITH POLLUTION LIMP HOME MODE ETC. I BOUGHT A NEW AIR FLOW METER AND REPLACED AIR FILTER AND IT IS...
Hi, when you get problems they seemto come in three,s --like the buses after wating 30 minutes!! Well,after passing the mot in France just 3 days ago my C5...
... Citroen are the only source I know of, however the switch is actually a suprisingly good quality device and after I changed mine I discovered that the...
WELL SINCE NO REPLY I HAD TO TAKE CAR TO GARAGE TODAY AS I MEASUERD A SMALL LOSS OF FLUID WHEN CAR PARKED OVERNIGHT BY PUTTING PENCIL MARK ON FLUID CONTAINER. ...
is it dripping in the car from the brake master cylinder and soaking up in the carpet? I'm not familiar with this car excuse me if this is a stupid thought. ...
In a message dated 04/11/2009 22:23:41 GMT Standard Time, cgat@... writes: WITH SUSPENSION DRPPING SLIGHTLY WHEN PARKING OVERNIGHT CAN THIS MAKE...
Richardomorris@...
Nov 5, 2009 8:00 am
16771
Sorry I mis lead both repliers to my question. This was a typing error.I MEANT TO SAY WHEN CAR , AS NORMAL, WHEN YOU STOP,THE SUSPENSION IS DROPPING IN...
update-garage said nothing found. I checked fluid level and it was at max.level so they must have topped it up as the other day the garage said level was ok...
For 3 years the current mpg display showed the mpg at all times regarless of the car moving or being stationary (engine running). Yesterday this changed to the...
Hi Dave, When stationary (engine running) the display shows no mpg and the small display goes grey and fades. When moving and presumably doing less then 99 mpg...
Just started the engine-havn't yet checked whilst moving. It shows 3 dotted lines for mpg. Display is Range, mpg, distance to destination.(this even though...
In a message dated 06/11/2009 11:41:48 GMT Standard Time, davewk80@... writes: When stationary (engine running) the display shows no mpg and the small...
Richardomorris@...
Nov 6, 2009 11:49 am
16779
What a nightmare! After recently buying the car, the rear nearside wheel starting to make a metal rubbing noise. So i decided to take off the wheel and check...
Hi, Does anyone know how to remove the green multifuntion display on the dashboard? I think one of the backlight bulbs has gone. If I could get it out I could...
Hi, Did you remove the corrosion that builds up between the caliper and the suspension arm due to their being dissimilar metals? This jacks out the caliper and...
You're lucky the bolts came out. Sometimes they have to be drilled because they are put in with locktite + years of corrosion. Some guys pass a drill...
Hi, I put a wire brush to all parts including this and scrubbed away a lot of dirt and corrosio and then gave it a quick clean. I think i might have to put...
The way to remove the Loctited screws is to heat them up with a high power soldering iron first and then remove them. I'm surprised copper grease is still...
Hi everyone, I have done this job a few times here is my experience. Alloy caliper bolted to steel suspension arm, with no gasket spells corrosion between the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
