When I had my Blast, I made the following mods: Rejet carb and install K&N air filter p/n BU-5000 Vance & Hines Exhaust (White Brothers is a quieter option) It...
The widest tire I found in my Metzler specs was a 200/50R17 MEZ3. The acceptable rim widths for that tire are from 6.00 - 6.50 inches. A 220 would want...
Hey Everyone, My Speedo just took a shit. It has power but getting no signal from the Trans speed sensor. I have heard this is a common issue. Anyone have an...
it might be as simple as pulling the sensor from the transmission housing and cleaning it off. it's not uncommon for it to get gunked up with metal shavings,...
Long story short - putting my primary cover back on - two things must be new - the gasket and the shift shaft oil seal. When I pulled the cover off it must...
The opening is towards the inside, the metal flat section outside (which makes it easy to tap it on with a socket) Ed I'd recommend putting the seal on after...
You see I read the BADWEB archives on this but there are no direct references - wrap the splines in electrical tape and use a 1/4 piece of pvc to guide the...
There's a recess in the primary cover for the seal. Basically you have the outer flat portion of the seal flush with the primary. The lip is inside (as is...
Thanks Ed - its much clearer in my mind now - I'll get back to you with results in a few days. Thanks again! Ed Z ... you have the ... is inside ... the...
Hi all together, I need some advise on exhaust systems. I'll fit soon a supercharger to my '98 M2 and want to fit the exhaust system with the higher gas flow ...
... installed. They use a tool similar to a valve stem seal tool, just bigger. If you coat one side of the primary cover gasket with a little grease and scotch...
As i've been riding lately I hear a noise out of the primary case whenever I'm riding high speed in a gear ,40-45 mph in 3rd, ect.. for all gears. When in...
... The primary chain tension is set by first backing off the locknut and the tensioner. Tighten the tensionser adjuster screw to 24 in lb and then back it...
I rode an XB12s today on a demo ride, smooth ride, good power and fun but to freaking small! If I was 5'4'' and a buck forty five I could have great time on...
... fit. How big are you? Big guys ride these I know, but it remindes me of the cinderella story. Sort of like the female (I think) down the street. I know she...
Well, this old lady (I'm over a decade past 39) could use to lose a few pounds, but her M2L fits her 5' 8" frame just fine. As for the fat ladies and gentleman...
... AZ transplant by way of MN, I know that area well. This time of year, (115) wish I were up there. Guy In Buell_Tech@yahoogroups.com, GearHeadGrrrl...
Hello all, I need a bit of advice. One of my exhuast studs on the rear cyclinder broke just inside the hole. How can I remove this and why would it break?...
Hey Jason Get a easy-out set and drill the appropriate sized hole with a left hand drill, even if you have to order it. Or you could get the screw remover from...
I have lean running problems (drones, is flat and sometimes coughs and surges) when steady at 60-110 kph on my '99 X1 which you can feel getting worse the...
I had the same problem until I installed the full Buell Race system. Jason ... __________________________________ Do you Yahoo!? New and Improved Yahoo! Mail -...
I was advised that the length of the race header was designed to allow equal length of the pipes and equal scavenging from each pipe before entering into the...
Cowen, John J
John_Cowen@...
Jun 22, 2004 3:15 pm
939
Also, I cleared up a lot of the surging and dead spot problems by going back to the stock airbox snorkle and keeping the K&N filter. Jason ... ...
