Has anyone seen any good write ups or any other aftermarket stuff to relocate the license plate and get rid of the fender type thing that it hangs on? Thanks ...
do you mean where the wiring connector comes out on the bike, or which wires are connected to it? the accessory fuse feeds the orange-and-white line, so any...
hey Sam this is one taht american sportbike sells. It lokks pretty good but its pricy, there is a guy on ebay that sells them for a lot cheaper less the...
posting for a friend: 2001 X1, ~5000 miles; power commander and aftermarket pipe (don't know what kind); yellow & nuclear blue. he's asking ~$6500. if you're...
Hi, I had the local HD/Buell shop install the Race ECM and so far I'm not too happy with it. It really bogs bad at WFO around 3000-4000RPM. I thought this...
I personally am looking to get another stock pipe. So let me know if you dump it. As for quite and performance. They do not go together. Free breathing ...
Cowen, John J
John_Cowen@...
Jul 15, 2003 4:26 pm
476
I have a stock pipe, 300 miles on it... excellent condition... make offer. ... From: Cowen, John J To: 'Buell_Tech@yahoogroups.com' Sent: Tuesday, July 15,...
Does anyone how to get hold of a scanalyzer and how much it cost? Does anybody make an after market version or PC version? Apparently you can program the ...
I would need it for a 2001 X1. If that makes a difference. Does yours fit that description? ... From: Eric Fenton [mailto:ejfenton@...] Sent:...
Cowen, John J
John_Cowen@...
Jul 15, 2003 5:23 pm
479
This is off my 2001 X1. stock exhaust ... From: Cowen, John J To: 'Buell_Tech@yahoogroups.com' Sent: Tuesday, July 15, 2003 1:23 PM Subject: [Buell_Tech] X1...
let me add a data point for your interest: I have 99 S3, race ECM, K&N filter, stock exhaust. I noticed an increase after both (first ECM, then later the...
I'm not familiear with your set up (I have a 97 s3) but on your ECM , if it was designed for an after market race pipe and you have stock it would flow too...
Hopefully my ECM will learn, I have only about 100 miles on it right now, and the butt dyno says its making more power somewhere. THere is still a dog spot...
try some WD-40 on the idle adjustment screw. It should go lower than you'll need to go. ... Yes, this is true, to my understanding. A lot of my knowledge of...
Side note, I put the S3 handle bars on my X1 last week and the bike is 100% more comfortable. Yet I can still ride just as agressively as I did before. I am...
Check with Sargent http://www.sargentcycle.com/default2.html . They don't list Buell specifically on their website, but they can make anything. Of course Buell...
Bars~ I resently did the same swap on my M2L, BUT the S3 bars were too narrow between the vertical section for the M2 double inst. dash ('01- '02 w/ Tach). ...
The S3 bars fit perfectly on my X1, the only trouble was the left grip, it is glued to the bar and I had to cut it off the old ones to get the clutch level ...
I can still get about 50mpg with my race ecm/k&n filter on the long haul. I ride like a banshee, but don't weigh much. I noticed a slight decrease from 50 in...
just got it,love it!great fun to ride.unfortunately,didnt get the owners man. with it. if anyone has an owners man.and/or service man.for 2000 m2 cyclone, or...
Hi everyone, I'm new to Buells. I picked up a 97 s3t with 5100 miles and lots of extras.(that was two weeks ago it has 6300 miles now. Must say I think I found...
In a message dated 7/23/2003 8:17:00 AM Pacific Standard Time, ld4406pack@... writes: Welcome Louie. I am sure you will get your comments back, and they...
Well I got my second corbin seat yesterday, and it fits crappy like the first one. I had to really crank on it to get it on, now I can't get it off! I...
If you are having that much trouble with it I'd put a hold on the credit card payment until you get it resolved to your satisfaction. I've seen the quality of...
I want to get a Krank Vent for my 2002 EFI X1, but ET Performances web site doesn't specifiy which one to get for this bike. Any body using these or can ...
