I am in the beginning stage of creating the ulimate xb9 website. You must admit that we all need one! This site will be for both xb9r and xb9s models. The site...
Sad damn story.......................... I upgraded with the Tach kit and in the process my Speedo quit! The Tach works fine (oh yeah!) and my Speedo shows...
My speedo stopped working a while back - the newer ones have an electronic pickup on the tranny - you didn't say what year you have - oh wait, yes you did! ...
the speedo is held in the housing by the screws on the back that connect to the wiring. if the speedo moved in its housing, it's possible that the speed signal...
Just something that i started, a lot of good links. http://autos.groups.yahoo.com/group/buellparts/ Stop by and take a look and add to it OPHAWK 98 S-1...
Any one had experience welding on a set of Buell cases? Bought a wreck and the rear engine/transmission flange that attaches to the swing arm carrier (better...
note that I'm *not* an experienced welder, so I don't have any technical advice for you. however I do want to point out that buell engine cases, as fitted in...
I believe, if done properly, a weld can be stronger than the original material. The flange I believe you are talking about is not a super-important one, ...
The welding has begun and has gone better than expected. Because the broken rear mount is something of an appendage to the cases heat transfer to critical...
your S3 fairing is fiberglas. if I remember correctly, it's got a primer coat, a color coat, and a clear coat on it - I don't think it's got a gel coat under...
Thanks its a '99 and it does go all the way through it fell on the trailer on the way to the shop (old tie down!) man was I pissed it didn't have a mark on...
if the paint side isn't too badly damaged, and it's just a clean crack through the fiberglas, you can try a patch on the inside. use a fiberglas patch kit like...
... S3. anyone interested in trading a buell race ECM for a powercommander? Hmmmm.... gotta think that through. YOu have all the goodies that come with the...
the stock ECM is, unfortunately, not programmable, so there's no software to control it. the only computer system that will interface with the stock ECM is the...
Hi there everyone, i am looking to make a front and back bike stands for my 98 S-1, does anyone have any plains to make them or know of a web site that may...
Has any one tried or considered using the hollow cast aluminum swing arm on the '99-'02's as an auxilllary oil reservior and cooler. It will hold 2+ quarts!...
With that much surface area the oil would run cooler. I'd love to see if it works. Jim ... From: awfijr [mailto:awfijr@...] Sent: Monday, May 19, 2003...
Thanks Wolf. If you learn anything let me know. -Mike Autronics A Curtiss-Wright Company Michael Edwards Senior PCB Designer Autronics Corporation 12701...
only thing I have to say is be careful to try to keep the oil near the pivot mount. two quarts of oil is pretty heavy, and I'd be concerned about it weighing...
I have run into a problem with my 99 X1, and hoping I can get some insight...... My bike is missing shifts at high RPMs. When upshifting, the pedal will move...
From easiest to hardest - 1) make sure the linkage has little free-play, and that it goes through the full range of movement without binding up. It may be...
I have a 97 S1 Lightning with a bad main drive gear bearing (transmission output) In order to replace this bearing I have to remove the transmission sprocket...
I use a large socket and a double-hammer Ingersoll-Rand impact. This is one time that manual tools don't cut it. You could try one of the impact drivers that...
I know others have mentioned the headwork done by Nallin Racing on their Buells, but I just got a set of Evo heads back from them and am amazed at the quality...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
