hi.. new buell owner here from indiana.. i got a 99 cyclone pretty cheap and i was wondering about possible problems...this is a strong running bike and i...
... Hello and welcome to the wonderful world of Buells. I recently picked up a 2000 M2 Cyclone and, although my front rotor doesn't rattle at idle, the only...
N, There used to be a kit to replace the "buttons" on the older rotors, but they would eventually start to rattle again. The later rotors don't rattle. It...
All: I have a problem with my 2000 X1 Lightning that I hope sounds familiar to someone out there that has been down this road before. First, the bike is...
Only on altitude changes like going up a mountain. This has been described to me as an inability for the system to change fast enough to compensate for the...
Hi Everyone, been lurking around the group for a while now and thought I would say Hello. I ride a 97 Thunderbolt S3T, purchased back in April of this year. A...
... When I bought my 97 S3 new in 97 it was actually un-rideable because the carb was so lean. The dealer put a jet kit in it for free and it got much better,...
I know that this may sound a bit simple, but, can anyone recommend a good outdoor waterproof cover for a Buell M2? I have seen them range from $25 to over a...
Rod, I wanted to invite you to check out my site. www.buellforums.com We cater to Buells and Hogs. Its only a couple months old and we could use some help. We...
Hi, I've an '07 TT that I'm converting to windshield/flyscreen offof a Uly .. . . the carrier sub-assemblies are quite different & need to be changed out .. .I...
Bruce, you need a Tamper resistant (security) 45mm Torx bit. I do not know anything about suppliers in NZ but I found a comprehensive kit of tool bits...
Has anyone totally disassembles wheels before? I have a 2000 M2 and am taking off the wheels and disassembling them to have them powder coated. I have a...
... you can just knock them out from the back side of them but go get new ones when you put it back together ii have done it a couple of times it works fine ...
Replacing them isn't a problem as I see that the two front bearings are only about $9 each, but the left rear bearing is about $45. Do they all need to be...
Are they PM spun aluminum wheels, or painted Castalloys? Be VERY careful with PMs, as the aluminum is very soft and can be damaged easily (I would only use a...
Thanks for the advice. I hate to admit that I don't know what PM stands for, but the parts manual that I have for the bike says that the wheels are cast alloy...
Diver, PM stands for Performance Machine, maker of high-end Harley wheels. They made one model for the tube-framed Buells (no longer) that were an option from...
Thanks for the advice. In the past, when I used to work on cars, I would use a large socket to install some bearings. I'm going to take a look once I get the...
is this the seat you want? http://www.badweatherbikers.com/buell/messages/21/320746.html?1199760655 i bought this bike, but the seat was too wide/tall for me. ...
Yep, That's the one I'm looking for. I'm in Orange County, don't know how far/close that would be to you. Shoot me an email and we can work out the details...
when are you going to make it to an ASBN meeting now that you are in northern cal? REX **************Biggest Grammy Award surprises of all time on AOL Music. ...
... Hey Buell Girlie, I think I "know" you. Well, I bought a part from you anyway off of the BadWeatherBikers BBS. Didn't you move to China about a year +/-...
march? april? the date of the jan one was actually the DAY i bought my bike, but it was just too hectic i honestly forgot about the feb one...and i just...
Jose - indeed. i'm active on badweb, and lived in China for most of 2007. i'm back in the USA now, and living in san francisco, working in san jose. what is...
Our meetings are always the first Monday of each month, regardless of holiday. sorry, we did not get the front page of the website changed. thanks REX ...
