<<has anyone ever come upon an acceptable add on right side mirror for an'84?ml>> I believe that they're from contemporary Fiats and Lancias. Mike. [Non-text...
From an RHD Maserati biturbo, probably speak to David Askew. My Spyder has both sides. Steve. Stephen J. Garran Golden, CO (Temporarily: Canberra, Australia) ...
As I mentioned previously, my manual 228 is currently suffering a very mildly blown head gasket, consequently I've been trying to figure out how to resolve the...
Hey! * 1. Provide myself some cheap therapy and simply blow the car up. Because of a blown gasket??? Naahh!! * 2. Fix the engine, perhaps finding various ways...
Guys, I'm moving forward with a Motec M600 Install in April when I return to the US. In preparation I'm getting all the bits and pieces together. In order to ...
... Well, she and I go back a bit... this is just the latest. To be fair however, I have been insanely hard on this car. Lots of track time and lots of...
Rob, I have a 2.0 litre here in the U.S. and no body no nuthin' about them over here. They are very different than the earlier engines. They require a rear cam...
Rob & Bob, The guy that did the 2.8 24 valve conversion is in Canada near Vancouver. Actually, he is on assignment in Europe at the moment. I have his address...
Didn't he start this project in California then had to move to Canada because it was costing so much? ... Vancouver. ... address at ... worth the ... you will...
... Vito, of Santa Monica, a wise old mechanic who began his career in the Carrozeria Maserati, once told that an Italian car is like an Italian woman: when...
... Bob, If I recall, you live in South Jersey? Have you tried Algar Ferrari/Maserati in Bryn Mawr, about 15 miles west of Filthy on US 30? Mark Cedrone and...
Hey! * To be fair however, I have been insanely hard on this car. Lots of track time and lots of theraputic late night backroad driving. She has taken all the ...
I have indeed met them at track events. Very nice guys but they still don't know anything about these cars. So, you want I should train them on my dime at...
Hey! * I have a 2.0 litre here in the U.S. and no body no nuthin' about them over here. They are very different than the earlier engines. The sensor setup is...
Hey! * The guy that did the 2.8 24 valve conversion is in Canada near Vancouver. Actually, he is on assignment in Europe at the moment. I have his address at ...
Hi All, Well there are a few that have done the 4 valve conversion and that is exactly what my 430 4V is. My car started life as a US market 430 left hand...
I have some slight seeping from the 2 small tell tale holes in the diff case inboard of the rear half shaft flanges. My car has the later torsion diff with a...
dude, don't spoil it for me. it just so happens i'm reading (ok listening to the book on tape) mario puzo's "the family" this week. the best part is that i'm...
In the car hey? I don't think so but we'll discuss this in a couple of days when I get my computers back on-line. I gotta dissapear for a while, house...
... I used an old Escort Cosworth ECU (practically identical to ours), desoldered the pins from the board, straightened them, soldered wires to them and then...
Hey Bob! It's probably easier to do the chain swapping with the engine out of the car. But, if you put the engine on TDC and lock it somehow, then you need to...
In a message dated 3/2/2005 3:35:52 AM Pacific Standard Time, ... Ha, CA smog! Be prepared to place the stock engine in it and each and every connection...
"It's probably easier to do the chain swapping with the engine out of the car. But, if you put the engine on TDC and lock it somehow, then you need to take off...
Hey! If you ask Bill McGrath they say that there's no set change intervall for the chains. They check them at the intervalls, and if they are worn they change...
If you put new chains in then the timing relationship between the two cams will be different due to stretching of the old chains. You can of course just leave...
Hey! * If you put new chains in then the timing relationship between the two cams will be different due to stretching of the old chains. On top of each cam...
If the head gasket is only mildly blown, have you thought of putting in something like Barz-Leak amd leaving the cap loose so that the cooling system won't...
I was told in this group you do some "wicked wicked things to biturbos LOL. Refered here by another member :o). You should all be ashamed of yourselfs or...
