Hello Rockyttyrone, Yes, it's the same fluid as used for the Autom. transmission: ATF Dexron II, specs: GM 6032-M For the underhood: 3M has very good adhesives...
Hi all Has anyone replaced the headliner in a Biturbo coupe ? Looks pretty straght forward. Apears to be only 2 rec, pieces of foam. Even looks like I could...
Well guys, Thanks for all the advice. I didn't get David's suggestions till afterward so some I learn't the hard way. Summary: a) I need lots of practice b)...
oh man, this is proving to be a bit more than i thought! the caliper bolts right up no problems there, the lines fit perfect too, so do the pads. i had the...
OK, the smog test dude is pretty sure my problem lies in the ignition cap and rotor -- it's arcing, you see. Does anybody know if the caps/rotors for the...
My dual coils arrived this afternoon. I have them installed, but not wired up as of yet. I actually had a little fun coming up with a mounting plate for the ...
I was out for one of my first spring drives in my '87 Biturbo Si. I was taking a corner in a very aggresive fashion and what to my surprise is that STOP SIGN...
Well I hope you had fun, sounds like it! Sorry you didn't get the rest of the info before your runs :(( a. freeway on/off ramps that are flat are good...
Cant you use some spacers ? Best regards, Pascal ... From: Matthew Savini To: BiturboZentrum@yahoogroups.com Sent: Wednesday, April 02, 2003 12:46 AM Subject:...
... I recently removed my headliner as it was hanging down. Remove the side covers by unscrewing the handles then pop them off. There is a center bar that will...
Thanks Chuck I'm fairly sure you can buy headliner foam somewhere. Just saw something on TV about replacing it. "Road and Track" Or "Car and Driver" TNT...
sweet fancy moses! you bought two of the 140009 coils? oh man! okay, unless you want to keep relpacing caps and rotors (mostly the rotor for some reason) make...
if you are cornering hard any application of the brakes will cause it to spin out. and the reason yours spins out faster and is harder to recover is the thick...
that would make it worse, i have to go the otherway and make something thinner. matt ... caliper ... do ... with ... maser ... allow ... the ... than ... ...
Ugh! Did Robert have this much trouble when he did his track car? If I'm understanding your problem correctly I suppose you could turn the rotors a bit? Keep...
I too am following this thread with interest. Since I think I warped my solid disks last track day ! If you swapped the front suspension, wouldn't you be...
Unl;ess I'm misunderstanding what your doing there is no need to do half of what has been suggested here. No fuel lines need to be touched. You don't need to...
Yeah you'd have that as a problem but the latter suspension is soooo much better. No more 55 MPH steering wheel jitters. Didn't he start with a a later car...
Think I warped mine 'cos the callipers have got lazy, not returning fully. Pads came out worn at an angle. Did it at Bruntingthorpe airfield, an old US air...
for the disc then ?? ... From: Matthew Savini To: BiturboZentrum@yahoogroups.com Sent: Wednesday, April 02, 2003 2:32 PM Subject: [BiturboZentrum] Re: back the...
* Of course most parts cars are probably wrecked in the front but I wonder if anyone has done it? I have! Changed the entire front and back suspension. ...
* Did you uprate the front brakes when you did you 4v and Racing suspension swap ? Yup! Did the works. Changed the entire front subframe and rear subframe. ...
If you have an automatic, make sure you tell them you have a ZF-3HP22. There's a special testing procedure for this tranny (something about not being able to...
The car's have always been tail happy. The big anti-sway bars, limited slip and fat tires don't do you any favors either. The help as long as you have...
... Well, I find the pathetic steering ratio makes it quite easy to pop back into line myself. That sort of made up for it taking twenty seven turns lock to...
Matthew: Good thing you offered up this FYI! A distributor rotor for my 1991 hovers $100? GULP! And if that's not crazy enough, there's a dowel pin that holds...
I am pretty sure I didn't mix up the coil wire, (ie wrong coil wire going to the distributor cap). But if by some twisted fate that I did, would this have...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
