Hi Neil The best person to talk to would be peter from T&G Motorcycles, I have attached there catalogue, Phone number is 01908 579799 I hope this is of help ...
Could anyone post on here the full chain size for a Bantam D14 please? I have tried Haynes and the index says it is on page 14, well not on my copy it isn't!...
There is the full D14/4 workshop manual available for free download on Tom's website http://www.bsabantam.co.uk/. Suggest you look there - there is a section...
Many thanks for that Stuart, 0•500 × 0•205 × 120 linksFound it there. Regards, Matchy ... From: STUART SEALE <stuartseale@...> Subject: RE: [BSA...
Hi Neil, Changing the big end on all Bantams is a specialist job. Basically: Separate the flywheels using a press. Press in a new conrod complete with new big...
Does anybody have the contact details of an auto jumbler who was at the Ringwood A/J on Sunday.He sells mostly Bantam parts, and lives in Chippenham Wilts. I...
His name is John Bull. Tel No. 01225 742091 Richard ... From: Michael Mais To: BSABantam@yahoogroups.com Sent: Wednesday, October 01, 2008 10:20 PM Subject:...
I have asked this elsewhere on the Net had had varying answers, so will see what comes up here! What tyre pressures would you recommend for someone (me!) of 17...
A lot depends on the type of tyres you are using and the type of riding you are doing. The old 1968 recommendations probably do not apply to modern tyres with...
If you were to use the handbook guide,it would be: +1psi per 28lbs over 140lbs (front) = 19.5psi +1psi per 14lbs over 140lbs (rear) = 31psi ... stone ... ...
Thanks for the compression ratio information. Next question ... Where can I get a fork shock absorber for my D1? The rubber bit that sits inside the spring. ...
Had some time on my hands and a D7 engine with a very badly worn crankshaft timing cover bush, flywheel had blued and worn the segments of the stator plates.I...
Was talking to Kevin a month or two ago and he mentioned how he'd been getting bantam stuff re-manufactured but hadn't had much luck with the harnesses because...
having rebuilt a few engines I thought I'd pass on a few tips. (been in the lawnmower trade for 20 years) first tip is don't be too pedantic about getting that...
Had the usual trouble with my d7's oval drums decided to strip it all down sand blast and re-paint and do the drums at the same time although I'd never done...
Always stick the case in the oven when trying to remove either bearings or spuds (Ulster speak for crankcase bushings/ locating bushes) George From:...
I was just wondering if the chap who had all that trouble a couple of months ago with his bantam front brake maybe had a lot of wear in the bushing in the...
Hi David I still havn,t found them,but I have sent a sample away to the guys who are re-manufacturing Amal carb parts, they are looking at the samples of early...
Also, Make sure she is out for a couple of hrs, close the internal kitchen door and open wide the back door if you can. And disconnect the smoke alarm, 'cause...
The bike died a death the other day so altered the points to .015 as per normal. Also noticed fuel pipe leaking at the base as not enough squirt at the...
Noel, Best advice for more speed. Wait until Halloween and get a couple of Chinese rockets, try either the Lake District or closer to home and easier .. the...
Hi Noel To get more speed out of your Bantam take the baffles out, according to the youngsters on their rev,n,go scooters flying??? up and down the road...
Or rig up a sail! Nitros even if you want to see the inside of the engine without removing a single screw. Kind of a partial engine engine strip whilst on...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
