Dear all I bought a 1968 Bushman when I was 16 in 1976 and rode it through my early 20's. Since then (the 80's) it's been sitting in a garage gathering dust,...
john , what sort of money are you looking at for the bike? although i am in lancashire , i have friends in london , that might be able to collect/store the...
well yes , well no. set off to work this morning at 05.00am dropped a barrel off to be bored +30 and supplied the borer with a new "guenuine" bsa piston , left...
Alan read your message on the message board with interest. I am roughly in the same position with a cracked not broken D7 crank. Just had it rebored, piston,...
... you ... hi ron , after breaking mine (with a lot of damage) on sunday , i scourd ebay and all the bantam sites , but to no avail , in my favorates section...
Hi Guys, I have a complete D7 engine in my garage which seems in reasonable condition (needs a bit of a clean up), although I have never had it running. The...
hi all a coupl of weeks ago someone put me on the right track with my D7 fork oil seals. I now have theoil seals (scraper type) can someone tell me wich way...
Hi Roy. The scraper lip faces downwards. David ... From: royston hooper To: bsabantam@yahoogroups.com Sent: Sunday, August 06, 2006 12:00 PM Subject: [BSA...
I am now at a loss and am getting so many conflicting opinions on whether or not the bike should fire even if there is something machanically wrong ie: big end...
... is ... shooting ... fuel ... stop ... some ... if ... mark , sorry to hear about your daughter, gearbox oil low = no problems with starting small end brg =...
Alan, the seals are in the chrome nuts at the top of the outer tube on D10 forks. The ones that are tightened with a "c" spanner. There should be a brass gland...
thanks kieth , i deleted my question , after looking thru a load of parts lists on line , can u clarify: 1: the seal is like an "o" ring , and fits in a 1/16th...
hi alan, yes it is like an rubber o ring but from memory it is a cupped seal with a small spring in it but don,t quote me and no to your second question - no...
thanks kieth , see http://www.ras675.co.uk/files/D7_Pastoral_Trail.pdf page 23 item on right , 10290-5269 , discription says washer , can,t see any on my bike...
The points on my D10 keep arcing when attached to the bike.Off the bike they behave as they should. I assume there should be some insulation between the points...
Hi. They are insulated from the engine but there should also be a condenser connected in parallel from the points to the earth. this is there to stop the...
Thanks David for the direction of the oil seal, all is well. Can anyone tell me where ican find a nut and bolt parts list for a early d7 I have been trying to...
Roy, the nuts for the suspension are probably BSF and the nuts on the top of the forks BSCy. Try lightening spares in Sale Manchester, he is very helpful...
... go to http://www.ras675.co.uk/files/D7_Pastoral_Trail.pdf and d/load the file , i go to local nut and bolt stockist for my bits, choose a quiet time , and...
You`ll find all the bits you need at C&D Autos. Give them a ring, they`re really helpful. David. ... From: Roy To: BSABantam@yahoogroups.com Sent: Wednesday,...
Dear Alan, Rex and Debra, Thank you for your help thus far in trying to get my machine to go! Alan, I have done the easy start thing to death today to no...
... It ... tinkering ... barking ... 1/ take the plug out-- finger over plughole kick it over and the compression should blow past your finger 2/ use a known...
has anyone fitted or seen them used i have documentry evidence that they were used on the compatition d1/3 s in the early 50s my sizing seems to show 0.9999 in...
... 1958 and ... is there a skf type part no , and more importantly what is the hieght of the brg , i have a cup/cone here but no ball brgs spare , would ...
SRM do them for A10/A65s, I had read somewhere they may have them to fit a Bantam. I thought the competition Bantams had taper roller wheel bearings, don't...
... to fit a Bantam. ... don't know about head ... guessed it: E32005J. These ... down from 1" to 25mm ... to fit. ... shimming OD of bearing ... thanks john ,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
