... Probably 6.5 to 1ish. A common dodge was to saw quarter of an inch off the inlet lower of the piston to extend the induction phase (mine had that and...
The George Todd information suggested using one of his heads that was 11 : 1 ratio. That sounded like quite a change.I'm going to take my head off and try to...
If any of you are interested I have a George Todd Head for a 54-63 D1 (55mm cntres) for sale I paid £50 as I believed it was for a 175 So any takers? Drop me...
ok, I know I have been kind of lurking in this room and bellyaching about not being able to ride my Bantam cos they changed the law limiting me to a 125,...
Hi all…
Has anyone got a George Todd head for a 175 Bantam they want to sell? I'm a= fter an 11:1 head if any one has one. I have a load of Bantam 175 parts...
Andy : Check with Tom Hayes from post #1618. I think his George Todd head may be for a 175 and not a 125 D1. The 55mm centers don't match my D1. BTW I pulled...
Got one for a 125! Tom (UK) ... From: jimsbantam To: BSABantam@yahoogroups.com Sent: Thursday, September 09, 2004 8:03 PM Subject: [BSA Bantam] George Todd...
No definitely for a late D1 I think as I have early D1 = Too big and a 175 D7 Too small! Tom ... From: wilburwipstall To: BSABantam@yahoogroups.com Sent:...
Hi all have been watching the message board and seen all the talk on George Todd heads can someone please tell me who George Todd was or is and what he did...
I have a brand new (still in the box) 51/2 inch headlamp rim! Make me an offer! Tom (UK) ... From: royston hooper To: bsabantam@yahoogroups.com Sent: Saturday,...
Royston All about George Todd Tuning http://autos.groups.yahoo.com/group/BSABantam/files/Todd%20Bantam%20Tuning/ I have a brand new chrome (still in the box)...
George Todd was the 'God' of Bantam tuning and did much to turn the humble = fowl into a Racing Rooster! He was also one of the founders of the Bantam Racing...
Good evening Finally I am almost ready to paint the tank on my D5, Maroon and Cream, could someone point me in the direction of a tank template and a paint...
... sorry no templates ,,but a picci for you http://mysite.wanadoo- members.co.uk/kevins_pages/1958_d5.jpg the colours are bayard crimson and ford ivory. you...
My 1968 D14 has finally worn out its original rear tyre. The downpours this week have convinced me to invest in a new one. Can anyone tell me what is a good...
... downpours this ... what is a ... and ... you are lucky that yours is a 18in ,, 18in are fairly easily available ,,even down to looking at the local *ap...
the chain on my bantam , has broke again ,,this thing is rotton, so I start ringing around ,,and its a bit scarse and expensive ,the size is 1/2 x 3/16 , i...
... I ... 420 chain is fine, my sprockets are ancient but usable - it's the crappy chains that wear. The trick is to get the standard chain size available cut...
... size ... thanks for replying ,,i searched this and other forums looking for the answer , as i said before , i found this "Quote "It is an unusual size...
I have been struggling to obtain replacement tyres for a d1/d3 , the correct size is 2.75 x 19 ,, the only ones available are "cheng shin" , but having used...
Hello All A while ago i asked if i needed a brake light on My '49 D1 fo rego. it was suggested that I fit one anyway so I have finally got the light and the...
... the lighting coils where it feeds to the light switch. take a tee off at some point before the switch and take that to the brake light switch the other...
The dilema here is that the bike just doesn't produce enough power through direct lighting to power the brake light as well as the headlamp and tail. You will...
Does anyone know the correct linear measurement for timing rather than just 16.5 degrees. Why they couldn't give both or stick with e.g. 1/16th as for earlier...
