Hi Bob

The first thing I tried was a clean of all the boards and connectors as
it was really dirty, some one had had the back panel off but it looked
OK and all the connectors seemed to go in the right place.

I bit of a dig around on this connector show that there did seem to be
something coming out, but since I don't really know what I am looking
for... I have a mate who is a TV / monitor man so I am trying to visit
him....

The top bin is a "969-2" CPUl. There is a damaged area of board at the
fan end just corrosion and some bad looking joints, I am about to suck
the chips off and rework that area.

ASC option ???? There was no handheld key pad that came with it, whould
there be a connector installed that said something like that...

I might try some photos tomorrow night so you can see what I can see.

Thanks

Max


> Max it is acting like the CRTC Board is not initializing. This is the
> video controller PN5000929. Try reseating the board by first shutting
> down the unit and removing the back panel. The large square panel
> center right if you are looking at the unit from the back. It usually
> has a hook attached to it. IF this unit has the ASC option there
> should be a hand held keypad attached to the back of the unit. The
> CRTC board should be about the third or fourth board down. It has a
> VGA looking connector on the right side and a ribbon cable connector
> on the left side of the board. The edges of the boards have small
> flip out tabs. Flip these tabs towards the outer edge of the board
> and firmly snap the it out of the socket that it is plugged into.
> Reverse the procedure to snap it back in place. Check the other
> connectors while you are back there to make sure nothing is loose.
>
> Bob
>
> --- In Automotive_Equipment_Repair@yahoogroups.com, max <max@...> wrote:
>
>> Hi Bob
>>
>> Just went out to the workshop for a quick look..
>>
>> First power on "Fuel system" & "Special" flash and then "Auto mode" &
>> Cranking" come on and stay on.
>>
>> Yes it is 230 v
>>
>> Thanks
>>
>> Max
>>
>>
>>> Hi Max,
>>>
>>> If one or more LEDs stay on then the unit has locked up and it is
>>> setting a code through the LEDs. The monitor is probably ok and the
>>> problem would be in one of the PCBA's. I need to know which LED(s)
>>> are staying on. The LEDs turn on and off in sequence starting with
>>> the upper left working down the left column then down the right
>>> column. The pump is the 4gas cycling and sounds like it is working
>>> correctly.
>>>
>>> Does this unit have a 230v plug?
>>>
>>> Bob
>>>
>>> */max <max@...>/* wrote:
>>>
>>> Hi Bob
>>>
>>> Yes 2 red LEDs come up, forget which once though
>>> Yes the fan runs,
>>> Yes it beeps
>>> Yes there is some compressor or pump in there that runs for a few
>>> seconds and then stops.
>>>
>>> So that is what makes me think it is a video monitor problem
>>>
>>> Just bought the monitor into the shack, but checked and it is 115v
>>> !!!
>>> so there is a 230-115v tranny in there some where, guess what
>>>
> I don't
>
>>> keep no more......
>>>
>>> Might have to go see my mate tomorrow
>>>
>>> Thanks
>>>
>>> Max
>>>
>>> > Hi Max, I don't have any more manuals but mabye someone else
>>>
> does.
>
>>> >
>>> > Several factors could cause no video. Do any of the red LEDs
>>> light up
>>> > in the center of the analyzer? Does the fan in the back of
>>>
> the unit
>
>>> > run? Any beeping sounds when powering on?
>>> >
>>> > Bob
>>> >
>>> >
>>> > --- In Automotive_Equipment_Repair@yahoogroups.com
>>> <mailto:Automotive_Equipment_Repair%40yahoogroups.com>, "Max
>>>
> Wheatley"
>
>>> > <max@> wrote:
>>> >
>>> >> Hi Guys
>>> >>
>>> >> Anyone got a mtc manual for one of these.
>>> >>
>>> >> Like it has no video display ??
>>> >>
>>> >> Thanks
>>> >>
>>> >> Max
>>> >>
>>> >>
>>> >
>>> >
>>> >
>>> >
>>> >
>>> > Yahoo! Groups Links
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>> >
>>>
>>> --
>>>
>>> Max Wheatley
>>> max@... <mailto:max%40zl2max.gen.nz>
>>>
>>> __________________________________________________________
>>> Delivered using the Free Personal Edition of Mailtraq
>>> (www.mailtraq.com)
>>>
>>>
>>>
>>>
> ------------------------------------------------------------------------
>
>>> Yahoo! oneSearch: Finally, mobile search that gives answers
>>>
>>>
>
<http://us.rd.yahoo.com/evt=48252/*http://mobile.yahoo.com/mobileweb/onesearch?r\
efer=1ONXIC>,
>
>
>>> not web links.
>>>
>>>
> ------------------------------------------------------------------------
>
>>> No virus found in this incoming message.
>>> Checked by AVG Free Edition.
>>> Version: 7.5.472 / Virus Database: 269.8.13/844 - Release Date:
>>>
> 11/06/2007 5:10 p.m.
>
>>>
>>>
>> --
>>
>> Max Wheatley
>> max@...
>>
>>
>> ________________________________________________________________________
>> Delivered using the Free Personal Edition of Mailtraq (www.mailtraq.com)
>>
>>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>


--

Max Wheatley
max@...


________________________________________________________________________
Delivered using the Free Personal Edition of Mailtraq (www.mailtraq.com)