Automotive_Equipment_Repair : Message: Re: Allen 62-000 engine analyer mtc manual

Automotive_Equipment_Repair · Beissbarth / Bosch Service

Already a member? Sign in to Yahoo!

Yahoo! Groups Tips

Did you know...

Want to share photos of your group with the world? Add a group photo to Flickr.

Having problems with message search? Fill out this form to ensure your group is one of the first to be migrated to the new message search system.

Messages

Allen 62-000 engine analyer mtc manual

Reply | Forward

Message #37 of 45 |

Re: Allen 62-000 engine analyer mtc manual

Hi Max, I don't have any more manuals but mabye someone else does.

Several factors could cause no video. Do any of the red LEDs light up
in the center of the analyzer? Does the fan in the back of the unit
run? Any beeping sounds when powering on?

Bob

--- In Automotive_Equipment_Repair@yahoogroups.com, "Max Wheatley"
<max@...> wrote:
>
> Hi Guys
>
> Anyone got a mtc manual for one of these.
>
> Like it has no video display ??
>
> Thanks
>
> Max
>

Tue Jun 12, 2007 2:56 am

Show Message Option

"Bob" <midsouthequipment@...>

midsouthequi...

Offline

Message #37 of 45 |

Expand Messages	Author	Sort by Date
Hi Guys Anyone got a mtc manual for one of these. Like it has no video display ?? Thanks Max...	Max Wheatley max_wheatley	Jun 11, 2007 8:38 am
Hi Max, I don't have any more manuals but mabye someone else does. Several factors could cause no video. Do any of the red LEDs light up in the center of the...	Bob midsouthequi...	Jun 12, 2007 2:57 am
Hi Bob Yes 2 red LEDs come up, forget which once though Yes the fan runs, Yes it beeps Yes there is some compressor or pump in there that runs for a few ...	max max_wheatley	Jun 12, 2007 5:00 am
Hi Max, If one or more LEDs stay on then the unit has locked up and it is setting a code through the LEDs. The monitor is probably ok and the problem would be...	Bob R midsouthequi...	Jun 12, 2007 6:19 pm
Hi Bob Just went out to the workshop for a quick look.. First power on "Fuel system" & "Special" flash and then "Auto mode" & Cranking" come on and stay on. ...	max max_wheatley	Jun 13, 2007 7:53 am
Max it is acting like the CRTC Board is not initializing. This is the video controller PN5000929. Try reseating the board by first shutting down the unit and...	Bob midsouthequi...	Jun 16, 2007 1:51 pm
Hi Bob The first thing I tried was a clean of all the boards and connectors as it was really dirty, some one had had the back panel off but it looked OK and...	max max_wheatley	Jun 17, 2007 7:36 am
The ASC option would consist of a hard drive and floppy drive just to the left of the circuit boards. If there is nothing but a motor and squirrel cage fan...	Bob midsouthequi...	Jun 18, 2007 5:39 pm
Hi Bob OK no ASC option. Got monitor back, not sure if we went forward there or not... Finished 1st attempt at repairing CPU board.... It is pretty sad.... The...	max max_wheatley	Jun 22, 2007 11:36 pm
Hi Max, I know all about the eyesight going away... Yes circuit boards are still available. Let me know if you have any luck replacing some of the IC chips....	Bob midsouthequi...	Jun 27, 2007 3:21 am

< Prev Topic | Next Topic >

Copyright � 2009 Yahoo! Inc. All rights reserved.
Privacy Policy - Terms of Service - Guidelines - Help