... i did this on a ford i removed the odometer and turned them back by hand.i had to start at one end,hard to explain.when you sell the truck tell them the...
This does not apply to 6066 Chevy trucks but it does apply to anyone signed up for this list. If you have any more questions email me off list at...
6066_Chevy_Truck@yaho...
Feb 2, 2007 4:11 am
6758
hello everyone, wanted to thank you guy's for the good feed back..... joe1963chevy ... Have a burning question? Go to Yahoo! Answers and get answers from real...
Does federal law say the odometer can't go to 0 at 100,000 or 200,000 or 300,000 miles? If so, I'm in trouble... ;-) CA doesn't care on old cars either, but...
Below is the generic odometer statement that must be signed upon transfer of a title. Depending on the state it may appear on the title or a separate...
I want 5-speed OD in my '66 K10 with some granny-like poop on the bottom. I have been looking for one of the old NP540GO trannys out of the 1-ton trucks but...
... Well... I have been looking for one for my 1500, so I wouldn't look at you funny (even though I too am a GMC guy). *IF* you find one, be prepared to pay...
Ford had a 5-spd Granny Overdrive in the late 80's - early 90's. Could something like that be made to fit or modified? (I'd be willing to bet Ford didn't build...
I do have a 5 speed in mine that is direct in 4th. It is a NP but do not remember what the model was. It is still in my truck along with my Detroit which is ...
OK Guys (and any interested ladies); Here's what I am finding out. David's right - there just ain't any old 540 overdrives out there - Jolly has all of' em,...
hey guys this older 5 speed ?is this the one that came in the c-60 trucks ? i cant think what models came in a 1-tonner that was an od trans ? as far as the...
I think Jolly's site said GMC 4000 series trucks. BTW, most of that swell and hopefully accurate info was from Advance Adapters and TLC web sites. Mike in AZ ...
If you call around to the large truck junk yards, you can find 5 speeds, but they want a LOT of money for them. When I was looking for a 5 speed non OD trans I...
I am looking to install a Automatic steering column in my 65. I was wondering if any of you know if a 1972 chevy truck column is a direct bolt in or if it...
I did that in my 61. I had to shorten the column piece that fits into the rag joint. I sawed it in half, took out a few inches, ground it down to points on...
By the way, I changed the column out again to an early 90's van with the 700r4 indicator on the column when I added automatic transmission. When I did all...
Hey Guys, I need to replace the rear brakes (again). I did used the old bad drums last time as quick fix before the hoidays and now need the the complete job...
Also been thinkin bout the rear disc setups now available. I have seen stuff on line (Pirate 4x4 guys) using adapter brackets from Great Lakes Off Road on...
... I'd suggest changing to disc only if it is the cheaper option. Vehicles use the front brakes to stop. I think the figure I read indicated 80% or higher...
I believe the new drums will need new studs pressed in and "the rear hub inside of the drum" is bolted to the axle, but shouldn't need to be replaced unless...
I have a 1963 chevy long bed an I like to make it a short bed does any one know if a short bed would fit or what has to be done to make this happen, need help...
... The rear brakes are mostly there to help you stop in a straight line, so the rear doesn't try to get in front. Also, drums work a little better when...
As the wrench turns...... The savings on the rear disc is a bit beneficial, but with maintanence and ease of part availability on a full floater disc brake...
find a short frame is the safest way, that way you do not have to cut and weld. they do come in short wb pickups, suburbans and panels and when I take the body...
sure it would/may fit but you'd be left with a gap between the bed and the cab. there is a story done on one of the custom/classic truck mag websites - do a...
I want to do the disc up front but its very costly right now. for some w/t c20 it has been proposed to swap the front clip with later model for complete swap -...
60/40 on all most every automobile. ... The rear brakes are mostly there to help you stop in a straight line, so the rear doesn't try to get in front. Also,...
gentelmen i am putting my 66 uility up for sale it has a rebuilt sm420 trans and ive put in a 9/11 detroit looker drop out rear end 327 with a new edelbrock...
... Well, since I wasn't 100% sure about the number, I looked it up. Between 60 and 90 percent of the stopping is done by the front brakes. If you think about...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
