Cheapest prices? Check with the people here in the group... most of us have spare parts sittin around that will go for cheap. If not, there is a multitude of...
This does not apply to 6066 Chevy trucks but it does apply to anyone signed up for this list. If you have any more questions email me off list at...
6066_Chevy_Truck@yaho...
Apr 2, 2006 12:12 am
6039
http://ck6066.web1000.com/ This is a reminder that you are a member of the 6066 Chevrolet Trucks e-mail list. If you wish to remain on the list, you need to do...
6066_Chevy_Truck@yaho...
Apr 2, 2006 12:12 am
6040
Here's a list of places that will keep ya busy. -jeffrey http://www.picturetrail.com/jhicken =================== http://www.chevyduty.com <--- my favorite ...
I am selling my 1966 Chevy C-30 6cyl 1-ton Flatbed. (I have photos but dont know how to attach them here) The truck was sold originaly by Hary Marx Chevrolet...
I'm selling my 1966 C-10 "show truck". Baby on the way and need something more than a Sunday driver. Interested, please email me for details. Link to pics of...
Almost finished with thr 350 install in the 63. I went to wire in the alternator tonight and I noticed that my new alternator (spec'd out as a 74-350...
Located in Austin, TX. 235 has been completely re machined and has not been fired up. I hate to sell my dream project but life handed me differnet tasks....
I suspect that your '63 alternator is externally regulated (regulater is on the radiator support on the drivers side) and the newer unit may be internally ...
I know there must somewhere be a wealth of info available for my proposed swap but I don't know where to look. I want to get a big block and th400 or 700r4...
Anyone know if I need to "lift" engine to remove oil pan....got a 250 hooked to a 350TH (66 C-10) or is there enough clearance to drop it as is....BB ... New...
Don't know about that, but you might be able to drop it enough to change the gasket or R&R the oil pump. If you do raise the engine, make SURE of your lift,...
Hello all, I know this is a chevy web site but I am parting out a 65 gmc and the reson I am letting you know is because alot of the parts are the same. I...
Where are you located? From: "vwadiction" <vwadiction@...> Reply-To: 6066_Chevy_Truck@yahoogroups.com To: 6066_Chevy_Truck@yahoogroups.com Subject: [6066...
Dennis, Did your truck come with the V8? I am trying to put one in my 62. Could you possibly send me a e-photo of what the engine mounts look like? I am...
On this truck the front mount is a large bracket that mounts to the front of the small block, then one large bolt goes through the center to a cross member. ...
As weak as it looks, that horseshoe mount in the front and the two mounts on the cast iron bell housing in the back work great. Would I want to run 400 ...
All... I've got a 292 (on 66 frame) that was rebuilt back in 1998, but has only been started once (about 5 years ago)....We hooked up all the needed periphials...
Thanks much...raised it about 4 inches and pan slide right out....and thanks for the safety tip. Made sure everything was secure.....Steve finleyphoto@......
I just brought home a '63 and noticed that the speedometer said I was doing 80 mph when I was only doing 65 mph. The original owner put new tires on just...
What transmission do you have? If it was ever changed, say from a 3/4 or a 1-Ton then it's possible the speedo is geared for 16, 17 or maybe even 19-inch...
John, Thank you for your eagle eye. The link was to a truck site from the early origins of this list. Between Pat and myself, I believe we have eliminated all...
It has a 3 on the tree with a 283. The original owner said other than the engine it was as he bought it which is why I am suspecting the tires since it appears...
A lot of these trucks also had a very low rear axle ratio. 4.10's and 3.90's with 15 and 16 inch tires on 1/2 tons. Great for pulling stumps and climbing...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
