There is a website someone mentioned Bowtie Overdrives that have 60- 72 transmission cross members mounts. There's 2 different styles because of were the hand...
http://ck6066.web1000.com/ This is a reminder that you are a member of the 6066 Chevrolet Trucks e-mail list. If you wish to remain on the list, you need to do...
6066_Chevy_Truck@yaho...
Feb 2, 2006 12:20 am
5870
This does not apply to 6066 Chevy trucks but it does apply to anyone signed up for this list. If you have any more questions email me off list at...
6066_Chevy_Truck@yaho...
Feb 2, 2006 12:20 am
5871
www.performanceonline.com sell engine mounts and auto trans crossmember....
With a 700r4 3.42 gears will have you cruising at 80 mph at about 2100 to 2300 rpm depending on tire size. You should also think about what kind of cam you...
I yanked the 283 and 3 speed on the column and slipped in a 350 (about an '84) with a TH350 auto. I was going through the difficulty of locating a column too....
Hi, I'm gonna have to upgrade the capacity of the rear of my '66 C10. I need to confirm what the 3/4 ton trucks of this era had for a rearend. I've read they...
... Don't forget the springs. An axle is only part of the upgrade, without the suspension upgraded as well, you really won't gain much. -- - David R Leifheit ...
No haven't forgotten that. Plan is for new 3/4 ton springs (if I can find some), and an air spring overload set up. Need to make sure I get the right rear axle...
Let's see if I can remember all the things the shop had to do... I've got a 1965 c30 that had a 4spd Granny-low with a 292motor. I just had the 700R4 installed...
Devon, thanks for the reply. I have to figure out my rear end ratio to see if I need the overdrive or go with the TH350. I am going to try my luck at a local...
My 64 Crewie C20 is runnin an Eaton rearend. Not sure if it is s-f or f-f though. Not sure if Eaton was an upgrade due to the stretch. Good Luck! Norm ... ...
Btw the track arm mount for up to 66 and 67 and after is different. Not a direct swap over. You will have to relocate the track arm mount on the frame to make...
hi there do you have anymore pics on your crew cab project ?its been a long winter for most of us in the cold belt !i am always interested in anybodys projects...
Hey ya Mike, Work has slowed down here too. Trying to get my bikes winter chores taken care of right now: clutch and forks.... But after that, will start back...
Hi there, My name is Nick and I just joined the group. It's kinda funny though I visited the 64 crew website before i came to this message board, Very nice...
Hey Nick! Welcome and thanks! Not sure bout the numbers. I was talking to one guy and he thought it to be approx 500 per years 60-66 for Chevy and or GMC. I'm...
hi there i thought i would try 1 last time before e-bay or crusher to sell this rough 1963 red &white carryall w/gates would be a good builder some rust and...
I don't know how much applies to Chevrolet, but for GMC the factory made no crewcabs. Ambruster/Stageway did stretches for trucks and suburbans. Here is a...
Hello all, I'm replacing parts of the floor pan on my 66. I'd like to converse with others that have done this repair. What should I look out for, and how...
David, Floorpans are not too difficult. It also depends on what type of repair you are looking for. For a daily driver that you want to keep the water out, ...
Group, In my continuing quest to replace my manual trans with an anto. Will a steering column from a 67-72 Chevy fit in my '62 C-10. If so, will the linkage...
It will fit, but you may need to make modifications. For instance, the brackets that mount the old column need to be transferred to the new one. You need...
First, yes, the column from a '67-72 will slide right in with no problem. It'll look "period" correct, so unless you tell someone, they'll think it's stock. ...
What does the column shift linkage look like for this type set up....I've replaced my manual trranny with a 350th and purchased an automatic steering column...
Tim... Sounds like we're in the same boat....I've got a 350th and just purchased a auto steering column from a 66, but no linkage (tranny was manual). If you...
I have a 65 Suburban, and I had the tilt column, TH350, and the power steering out of a 72 Chevy Pickup put into it, and it works great. I already had the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
