Does anyone have a 3 spd trans that has the syncro 1st gear and OVERDRIVE ? for a 65/66 C-10 ?...............ED. [Non-text portions of this message have been...
http://ck6066.web1000.com/ This is a reminder that you are a member of the 6066 Chevrolet Trucks e-mail list. If you wish to remain on the list, you need to do...
6066_Chevy_Truck@yaho...
Mar 1, 2005 7:29 pm
4841
This does not apply to 6066 Chevy trucks but it does apply to anyone signed up for this list. If you have any more questions email me off list at...
6066_Chevy_Truck@yaho...
Mar 1, 2005 7:29 pm
4842
I replaced the 4-sp Saginaw car tranny someone had installed in my 63 with a SM420 ( keep tearing up those little car trannys) Now for the drive shaft.. the...
I have a 64 C20 with a SM 420 and it has a 2 piece driveshaft with a slip yoke on teh back driveshaft. You could use a one piece driveshaft if it has a slip...
At 11:28 PM 3/1/2005 +0000, you wrote: Ok maybe this will help me.. Anyone have a SM420 in a SWB ? Can you describe your drive shaft ? length ? I guess I'll be...
Does anyone have or knows where I can get the correct water temp. sender for a 1960 K-10? This is the one with a gauge , not a light. Also does anyone have an...
I just bought a temp sender for a gage for my '65 C-10 from the local Napa store this past Saturday. They even had it in stock. Said it was the same for...
Try these for your speedo. http://www.williamsons.com/ http://www.speedometershop.com/ ...
Mike & Kathy Gardner
mikath@...
Mar 3, 2005 12:24 am
4849
Speedometer Repair - Autocraft Electronics 972/466-6290. They repair, among other things, automobile instruments and stereos. They are a huge operation....
a list of links to websites for companies that sell parts for chevy/gmc trucks. Each listing states which year model trucks that company sells parts for. over...
Hi, Im a new proud owner of a 66' rust bucket. I can't find much information. It has a the staight six with a powerglide auto trans with matching numbers....
If you're a/c is hanging under the dash it is not factory. Chevy had built-in factory air by 66. ... From: motoxandhoneys [mailto:motoxandhoneys@...] ...
Chris only swap the motor if you think you need the power or want to drive long distances. That six cylinder has plenty of torque and gets decent gas mpg...
Chris: The trick is to find out which straight six you've got... I'm kind of partial to my 292 straight six in my 65 C30. To tell if you have the 292, look at...
i have a 63 k 20 and i need to get it out of the yard ill sell it cheap to someone that wants to come and get her im in western colorado970 275 5156 john...
AUTO TRANS IS REAR AND SO IS A/C WHAT ENG IS IN IT NOW ? PUT A GOOD OLD 350 OR EVEN BETTER A SMALL BLOCK THAT IS MY OPINION JOHN [Non-text portions of...
Anyone tell me how to remove the shifter on an SM420 ? no way to install it motor and all at once with that 5 foot shifter sticking up :) Can't find anything...
The easiest way that I know of is to unbolt the top cover on the trans. If you unbolt the floor pan above the trans in the cab its easy to reinstall the top...
At the base of the shifter there is a domed metal collar/retainer. You have to push down on the collar while turning it counterclockwise about 1/4 turn, to...
... Thanks for all those that replied off list. For some reason this just seems to have been posted and I emailed it on the 27, I got over 10 replies via ...
Hello all I have 65 chevy pickup with a rebuilt "79" 350 small block in it. anyone know where the timing should be set? my guess is 8 before. But it could be...
I have two short wheel base pickups with that transmission in them, a K-10 and a C-10. Both have one piece drive lines with a slip joint in it? I am wondering...
I don't know too much about setting the timing on a 350 other than it's probably pretty tolerant. I do know the optimal timing setting is dependent on how the...
... There is a slip joint in the end ? What does the SM420 have on it's end for connection ? Mine has a U-Joint end, so how does your slip joint connect to the...
I have the timing on my 305 set at about 10. Your 350 will be about the same. I would start at 10 and you can adjust it from there. Id set it so it doesnt ping...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
