http://ck6066.web1000.com/ This is a reminder that you are a member of the 6066 Chevrolet Trucks e-mail list. If you wish to remain on the list, you need to do...
6066_Chevy_Truck@yaho...
Jul 1, 2004 10:43 am
4191
This does not apply to 6066 Chevy trucks but it does apply to anyone signed up for this list. If you have any more questions email me off list at...
6066_Chevy_Truck@yaho...
Jul 1, 2004 10:43 am
4192
Im planning on replacing the six for a 350, I have seen trucks that have the engine moved forward about 2 inches to give the distributor clearance from the...
you are just the opposite of me. I have a 350 that I would like to change out for a str8 6. Here is the deal with mine. the drive shaft is short, it shows the...
hey Cyruss, Im living in "hells oven" better known as Phoenix Az. a bit of a drive from where your at. where did you get the 350 from? I just bought the truck...
went through the same thing on my burb. I have seen the forward mounts and wanted the extra room behind the dist. Since mine was a four speed I would have had...
Good luck with your swap. I moved my 350 up about 2.5 inches and swapped out my TH-350 for a 700R4. The extra length of the 700R4 allowed me to use the...
I swapped my 230 6 cyl for a 305 V8 and just reused the stock 6cyl mounts. I have a stock points distrubutor that clears with no problem. If you need room it...
Last fall I put a 1969 396 into the bay where the six once was. I used the stock mounts and the tranny and shaft were kept the same. The motor fit snuggly,...
I put a Chevy 350 into my truck as well as a Strip performance automatic TH350 Tranny and kept the original 2 piece drive shaft. my 1962 GMC longBed Fleetside...
Wow! Now your talkin... I was wondering how that two-piece shaft would hold up under the stress of the big block, been kinda ginger with it not wanting to...
I saw the sillyest d*** Thing today.Somebody with way to much time andmoney has built a FWD Pinto the bumpers sit about 3' off the groundand the thing was...
I presume you meant 4wd... :) So got any pictures of it? I have a spare Pinto and some Chevrolet parts... maybe I could do something bizarre with them... I...
I might have one that I had in my 61 4x4. Let me check an I'll get back to you. TTo be sure it'sthe motor mount for the the front of the motor right by the ...
Yes I did mean 4WD It looked as if it were on a GM or Ford Frame. Sorry no camera with me at the time. ... __________________________________________________ ...
Yes, it goes right under the harmonic balancer, at the very front of the oil pan. It has to be from a V-8, the six cylinder mount won't work. Thanks for...
does anyone know where i can find one or know of sheet fabricators who makes them. want something to match the rear ones thats out there, seem hard to find,...
Think your going to have to make one as I couldn't find one either. I replaced my front end with a tilt forward fiberglass front end and made my own by...
does anyone with a 60 to 62 with a torsion bar suspension have shocks mounted on the out side of the frame, I have an old 62 frame with out board shocks and...
They all have them. Add a sway bar front and rear and you can retain a much better ride than with coils. ... From: oldyellar632004 [mailto:oldyellar63@...]...
i am here in northeast iowa. i am really interested in the mount if you want to sell. let me know what you want for it. i will pay for shipping. dan noe...
Alright everyone here is a stumper. Everybody knows I got a 65 1T duL. This one got our dealer confused and it isnt covered in the Chilton Manual. On the rear...
Hey, I'm perplexed too... I've got a 65 C30 too, and it's got the same "shock mounts" on the axle but I don't have shock mounts on the frame. Anyone know...
... I am not sure I understand the confusion, are you saying the dealer is telling you that the truck doesn't need shocks? If so, you need to take your truck...
I remember reading somewhere that trucks with large spring packs may not need shocks due to the amount of friction caused by the leaves. When spring packs have...
new member here, i've got a 60 chevy apache suburban 4x4 that was converted to 1-ton by previous owner, it has original dana44 front end but hubs are 8-lug...
i have a 64 chevy short bed pickup with a V6 motor. The motor has been rebuilt, have a reciept for $2700 for this rebuild. I bought this from a guy I know....
... Chevrolet didn't have a v6 that year, so either that is a different (non-stock) motor or you have a GMC and not a Chevy. Just had someone with a similar...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
