To one and all, Happy New Year here is to a secure comfortable contentment in the new year. Thank you for being a part of my life. Sincerely, Tina and Family ...
This is a reminder that you are a member of the 6066 Chevrolet Trucks e-mail list. If you wish to remain on the list, you need to do nothing, this e-mail is...
6066_Chevy_Truck@yaho...
Jan 1, 2003 12:24 pm
1961
This does not apply to 6066 Chevy trucks but it does apply to anyone signed up for this list. If you have any more questions email me off list at...
6066_Chevy_Truck@yaho...
Jan 1, 2003 12:24 pm
1962
I'm needing a 60-62 V8 fan shroud for my pickup. This seems to be a very hard item for me to find. If any one can please help me locate one or have one they...
Tommy, Call Alan at County Line Classics. They are in Red Oak, Texas. (Just South Of Dallas) @ 972-223-3200. They have quite a few 60-66 salvage trucks. ...
hi all I have been in the club for a few months.The old p.c. went south a few weeks back this is the second time in two years.No more gateways for me.Yahoo ...
I would check the wrecking yards for a newer pickup or S10 setup. There should be something that could be adapted with a little searching and planning. Kenny...
Well I did not get much done on Sue new years day. Added an electric fuel pump,installed a speedo gear to trannyAnd ran down problem with the horn. I guess to...
My experience with fiberglass is that it doesn't expand and contract at the same rate as the metal it is used on. It cracked/separated partially after few...
Theuns Pelser
THEUNS.PELSER@...
Jan 2, 2003 1:55 pm
1974
Should bolt right up with no problems. I assume you are also using the front end off of the'72 for your disc brakes. It should bolt up also. If not, look at a...
I would go with the 327, just because there isn't a whole lot of them around any more. Build it with some compression(around 10:1) and it should run just...
I would go with the 327, just because there isn't a whole lot of them around any more. Build it with some compression(around 10:1) and it should run just...
Red, I no longer have the Dyno printout sheet, the numbers were obtained from a dyno at the rear wheels, the Hp caluclations were made by my partner who...
Well this it for a while until the funds build back up. The middle drive shaft from the 2 ton will fit perfectly. The radiator is 32" tall it will rest at the...
In need of parts truck. Body must be in good condition, no motor or tranny ok, I need the long fleetside and tailgate. I am located near Portland, OR, so I'm...
Hey Folks Came home about dark30y to find my headers had arrived. The flowtech look really good. I mustered enough energy to mount the right side; bolts up. ...
Doyle, This might sound funny, but I remember when younger I had installed headers and slightly dented them to get clearance, as long as they are not severly...
I put Flowtechs on a 66 I had,had to remove clutch linkage,install header,re-install linkage,was a bear to adjust afterwards but it all fit OK.Brian...
Does antone have a good idea on how to get my front windshield back in, I have the seals and everything else I need, I just dont want to break the original...
I have always used the rope trick,put rubber on glass,then put 1/4" nylon rope(I use pull starter rope) in pinchweld groove in rubber. You want to overlap rope...
Run a string/twine around gasket groove that goes against window frame, liquid soap an that groove right...Install gasket on window, have one person in side...
Greg and Peepeeman00 are all over it. Do it that way and you wont fail. I did it to my '62, (wrap around window), by myself, (not recommended), without any...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
