Ok, guys, this is kinduvvva strange request, but I gotta find something, here. Van. E350. 1986. OK, what I wanna do is take this one and put a pickup bed...
Well, if they said it was bent at the spindle, then the 70 won't offer any improvements in that department. And since you already have an ARB for the 61, it...
Robert, can i use the dana 61 ARB in the dana 60 front end? Robert Mann <robert.cobra46v8@...> wrote:Well, if they said it was bent at the spindle, then...
Chris, as it stands now the dana 60 front end is wider then the dana 61rear end will this make a differants using 10.5" 14 bolt and can i get the same gear...
Try 4x4trailers in the Las Vegas area. They have some great choices. Martin ... fabed side that will have the same wheel bolt pattern as the van. I like the...
The pads will have to be relocated, and you'll want to bend some new brake lines. 4.10's are available, and you already know about the Detroit. ARB just...
Hi, if I understand you right you want apiece that after you cut the rest of the van off just after the front seats is what I would call a bulkhead. We used to...
Woo-hoo!! Yes. yes, right behind the front seats at the aft doorpost is where the factory typically stops the sheetmetal for these "cutaway vans". They sell...
... Well that depends on all of the elements in the equation. Unfortunately right now I don't have a yes or no answer. 1.) Since you didn't state what kind of...
Thanks for the help. I ended up taking the resistor out of the good unit, and transplanting them into the old unit - just took some soldering and bending. So...
Note: forwarded message attached. ... Start your day with Yahoo! - make it your home page thanks keith for responding to my post. i am new a this 4x4 stuff...
Someone already explained about the things that need to be changed to stick a 14 bolt in, and most truck shops can do this if you do not wish to do the welding...
What is the web address of that site? Seth ... From: mark mays To: 4x4van@yahoogroups.com Sent: Tuesday, August 23, 2005 4:10 PM Subject: RE: [4x4van] try not...
Chris this sounds great,but does the width of the front end dana 60 make any differants in relationship to the rear end 14 bolt ? just try to figure out what...
The 14b and D70 are basically comparable in strength. Some will debate that, but it's democrats vs republicans, EFI vs carb, Ford v Chevy. Either is an...
Keith Lawyer
LawyerKG@...
Sep 2, 2005 2:34 pm
15399
I can find a pic of my old van that had a D60 front & 14 bolt rear so you can see the difference. The bolt on pinion of the 14 bolt is a major advantage in the...
I read the old posts and the newest one by keith and I am thinking that I would consider only two options. First I wanted to ask if this van stays fully loaded...
... Like I said earlier, I have a dually axle in my van. A 70U and if someone bends a 70's tube, well then my hat is off to you, and maybe a trip to Wendy's...
Is THAT what these are called?? I thought the Centurion was the Ford "suburban" back in the 80's before the Excursion/Explorer came out. They took a crewcab...
I'm not sure I completely understand the reasoning, but nothing wrong with thinking out of the box. A "dually axle" doesn't necessarily gain you anything....
Keith Lawyer
LawyerKG@...
Sep 2, 2005 3:37 pm
15404
Keith, a note on Ford dually axles. The locator pin was just 1 of the several changes from a srw. The other being they are about 2" wider on each side- and...
Hey Frank,or anyone, Ordered the Hellwig sway bar from Quigley and should get it next week.Question is,will this be a simple bolt on,any drilling required? Any...
Ok my take on the discusison.... If ya bent a Dana 61 in a van ya probably hit something, or someone else did (just my opinion) The Dana 70U is a good...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
