Turns out to be a 1990 F 350 caliper and I am sure others. Big though. Mike _____ From: 4x4van@yahoogroups.com [mailto:4x4van@yahoogroups.com] On Behalf Of ...
Greetings everyone. I'll check old posts later, but wanted to let you know that I'm starting 'the project' this weekend. My rig is a 1988 E350 with coil spring...
That's what I was thinking. Btw for clarification, there are a total of four torque arms, two on each side. I'm calling Quigley today, I'm going to need help...
1988 E350 Conversion Project Hey Shaun, that looks like the same type of front end I picked up in the junkyard - mine is a '97. Is that a Quigley's? Do you...
If the lower control arms are around 24" and the uppers are around 16" and made out of square stock, then it's Quigley. There's also a bracket that's welded...
frannyaj@...
Mar 12, 2010 3:47 pm
20813
If the lower control arms are around 24" and the uppers are around 16" and made out of square stock, then it's Quigley. There's also a bracket that's welded...
frannyaj@...
Mar 12, 2010 3:52 pm
20814
Thanks. Just talked to Jean at Quigley's, she's going to fax me some diagrams and part numbers on Monday, but she said that some of the parts may be obsolete....
They stopped aupporting a lot of items for the '91 and older models. A lot of the parts they've used are standard oem and some of them are Quigley parts. I...
frannyaj@...
Mar 12, 2010 4:24 pm
20816
Hello, This is Johnny, and i'm wondering if anyone can tell me if i can remove the air pump from the engine with out any negative effects. I have an 87 ford...
JOHNNY WALTHER
johnnywal@...
Mar 12, 2010 10:34 pm
20817
Hello everyone, I luckily just found this group, as I am looking into getting my first 4x4 van. I have my eye on one in particular, located in North Carolina...
Hi There, I have 1990 E350 4x4 extended ford van with wheel chair lift it has coil springs on a dana 44. the transfer case is mounted more to the middle of the...
Any pics? Chris Steuber www.ujointoffroad.com 818.606.5206 On Mar 13, 2010, at 2:08 PM, "Ron" <ford4x4van90@...> wrote: Hi There, I have 1990 E350 4x4...
Either a pathfinder or a quigley I bet. Does it have 4 arms holding the front axle or 2 that look similar to 2wd van? Sent from my iPhone On Mar 13, 2010, at...
I've removed mine with no known ill effects. The air pump scavenges exhaust from the exhaust manifold and pumps it into the intake stream to recycle some of...
Hi Paul, You just described the EGR (Exhaust Gas Recirculation) valve, not the air pump. Blocking the EGR can, in some instances, cause pinging/pre-detonition....
Hi Group, Here's a few pics ________________________________ From: Chris Steuber <cjsho2000@...> To: "4x4van@yahoogroups.com" <4x4van@yahoogroups.com> ...
Looks like a nice conversion. I would like to see more pics of the divorced NP205 crossmember/support. Also was the gas tank chopped? It looks like it was...
It looks like someone tried to copy a Pathfinder and failed miserably! The trackbar is too short and the angle is way off, the front driveshaft looks like it...
Hey thank you very much for the info. The cats were removed when i bought the van, so i thought i'ts not doing much good anyway. I'm from Canada, and there's...
JOHNNY WALTHER
johnnywal@...
Mar 15, 2010 10:22 pm
20830
Hey Group, Couple more pics ________________________________ From: "cfh421@..." <cfh421@...> To: "4x4van@yahoogroups.com" <4x4van@yahoogroups.com> ...
i want to insulation my van but don't know what insulation to use? what kind did you use...
t pitt
PITTOM@...
Mar 16, 2010 1:00 pm
20832
Check out JC Whitney they have all kinds to look over,then find out if their is a business in your that carries it check for heat restrictions. ... From: t...
You can use 1/2 in pink styrofoam from DIY store. Use 2 layers and adhere with spray adhesive. You can also use contact cement, but you only get 1 chance....
Those are Smok'en ideas and exactly what I'm doing with my van after putting the 4X4 frame l built out of another 1993 E-350 XLT Club replaced the floor...
If you are concerned about the heat from the exhaust, I would look into installing insulation specifically designed to reflect the heat away from the underside...
