Kind of off-topic, but what symptoms might a car show with an improperly connected O2 sensor at idle? Note, I didn't say not connected, so say the signal isn't...
Question 1. i recently took out the airbox and put in a cold air intake. as we all know the coil is mounted on top of the airbox. i screwed the coil throught...
Looking for a GTX center console (the part the shift boot and stereo mount to). I lost my spare to a second break into my car. NW is preferred to save on...
Ok installed the new TPS didn't fix it. Checked the AFM it's good and cleaned the connectors while I was at it. Checked the Relay under the ECU on the...
The sensor at the top of the radiator on the driver's side is a high speed fan sensor. The sensor at the bottom of the radiator on the driver's side is a...
No real way to check the injector function that I know of on a bench. Might as well pull them out and spend the $100 to have them cleaned. I guess you could...
I'm looking for 1 of these too, if there's a 2nd one around, and also thr handbrake cover part of the center console. I'm in NY, but location probably...
Or, look for a plug that is darker (in your case: much darker) than the others. Have you checked your turbo hoses? The one that comes off the turbo tends to...
Hey all, I just went to the dealer for a radiator, only to find they are not available. Any help/leads in finding a replacement would be appreciated. thanks, ...
International mazda meet Where: XXX Root Beer in Issaquah Washington: 98 NE Gilman Blvd, Issaquah, WA 98027 (425) 392-1266 When: August 23rd How much: FREE ...
Well its been a while since I've solicited this group to buy the remaining parts of my GTX, but don't think I've forgotten about you. The following is an...
I'm selling a brand new set of Goodridge stainless braided lines. New price was $120, selling for $50/b.o. I also have a bunch of miscellaneous new parts, many...
so i made a bracket to hold my coil and bolted it to the frame. ground the paint off anyything with paint on it and my car still wont run. i get fuel and air,...
So I finally got back to the brake upgrade yesterday. I tried the basic entry level pads from autozone without the shims already glued on and without the...
That's excellent news. I don't use the shims at all anymore for years now. Even on the back brakes. Greg Downing Beautiful Downtown Spanaway Washington, State....
Since the coil is already wired for 12 positive and negative I don't think that's your problem. Check the connections and voltage to the coil. Greg Downing ...
I think my grinding on the front caliper was the caliper body actually flexing as it rubbed the very outer edge of the rotor. A quick dremel job did the trick....
I'm redoing the suspension on my '88 GT. After disassembling the struts, it was apparent the rubber spring seats had seen better days. My dealer says those...
When I was running the ST springs I took the rubber pieces off that sit between the spring and perch. Never made any noise and the only issue I had was some...
That was my experience with the BPT and stock VJ20. I had it cranked to 17 psi but as it neared 5500 rpm's the boost would fall off and ended up at 12-13 psi...
I trimmed down the bump stops at the top of the bellows and used them that way. I think I left about 1" of the upper BS just in case of a hard hit on a ...
The stock VJ14 cannot pull 16 psi to redline. It poops out just like the VJ20 when you ask it for more. You can redline the BPT and VJ20 all day if you want....
The basics: Dead engine, good chassis, decent gearbox, LOTS of spare parts. The speedo cable was disconnected when purchased by the previous owner, but it's...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
