Rob, I would love the Autronics set up, certainly one of the best out there, if not THE best IMO, I have seen i used very succesfully on many cars, and there's...
June 27th at Portland International Raceway is a lapping day with the Alfa Club of Oregon. I plan on attending this event in the GTX. This event is a 1st come...
I have these same wheels sitting in my garage. I had to pick up a set after an endlink broke on my swaybar and caused my currnet enkeis with A520s to be...
Interesting that you mention this. I remember once in the past having a request to modify a honda ECU so it wouldn't look modified. I'm not sure if I...
Michael Richards
michael@...
Jun 1, 2004 8:58 pm
49146
Susp wise; Ground Control coilovers, with #375-#275 front/rear springs. These sit on the Dirtras. Camber plates in front with 1.5 negative camber, zero toe....
i got another motor and am think of building it. i was looking into things and i see that the b6t standard bore is 78-78.019mm. .25mm over is 78.25-78.269mm...
I'm planning on going. Is there any pre registration for the event? Or is it only pay as you show up? I haven't found any way to pre register. I'm still...
Guys, Does the civic alu rad setup allow a side-by-side intercooler in the GT-X? Cheers Adam (Still on the hunt for a BG GT-X in Sydney) ... into ... going to...
Great minds think alike. My Son won the Milwaukee Region SCCA autocross in F Street Prepared. Coil overs, 400 lbs/inch in front, no front swaybar. 325lbs/inch,...
Courtesy of Mr. Manspeaker, I was able to borrow a bore gauge and I checked out the cylinders this evening. They were all pretty close to each other and round...
Before you go out and spend big$ on a set of piston, measure the current size of your bore first. Use the biggest measuement you got from 3 position in each...
I've had mine bored out. I may have misunderstood, but when you say .25mm, are you sure you don't mean .025 in (.625mm)? My understanding from the Mazda...
Edward, .25mm is .0098in. Remember, there is 25.4mm in an inch. Dan 88GTX 90 protege 4WD ... that ... necessary, ... hardly ... English ... got ... go big ... ...
Alan, Looks like your block is already oversize, ie it has already been bored .25mm (.010"). Either get a new set of .25mm oversize rings, remove the glaze in...
I recently aquired a GTX with a modified ecu, Now I just noticed that it has a differnt number on the front cover (B6B4) but the inards look identical, does...
Hmmmm.....I dunno the only thing I can think of that would be different *IF* the harness is the same is the value of the MAP sensor going to the ECU Michael...
I'd call the 0.0015" (1.5 thousandths) the wear from ~150k miles. Not bad for a street engine if you ask me. I'd go with the 1st over rings and check them...
Well it works great now. I took a look at the valve and saw that I forgot to remove the plug on the "NC" port, duh I coulda sworn I did that.. Now my only...
... I suppose if I could get my hands on a NA ECU I could test it out. I always assumed that the pinouts are different. From my experience these things are...
Michael Richards
michael@...
Jun 2, 2004 8:14 pm
49162
actually i meant .25mm. if its wrong talk to mazda they published it in the mazda shop manual. .25 is .010 in. actually just under that. can you sleeve a the...
... If they do go too deep, just buy my b6t block, it's on its factory bore. So one overbore and you're good to go... with another machine shop, since you...
Hey is anyone from the Seattle area going to this thing? Derrick at CS says something's going on down there. Anyway, if you're going, please contact me... I'm...
Hey Jay! On the track this weekend at PIR (Portland) are Cascade Sports Car Club ICSCC races, with a race school on Friday.. We are headed up your way for the...
As adam saw from the pics of my set up the answer is yes. An even better set up would be a custom side-by-side pair that are identical in appearence but one is...
http://www.wwscc.org/event_results/2004/scca04-4.html#SM This was in the dry. I am slowly getting used to the new BG tranny. I run on 3 year old Kumho V700's...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
