Hey Gang! I toured the www.generationplastics.com facility yesterday with Nick and Sean. Nice place. That is the company that makes the side skirts for the...
I've found a replacement for the OEM J Spec side skirt trim that is cracked and or broken, It is identical to OEM, but flexible (not rigid like OEM) the only ...
Hey Guys, I pretty much like anything that says "Mazda" on it, but you should find this quite amusing. I found it while searching for information on another...
If there is anyone out there interested in a 88 GTX (cheap) drop me an e-mail construction_pm@yahoo. I inheritied this single owner car from my Dad (real motor...
Adam, the hubs and knuckle have to be pressed apart. Not easy for a garage do it your selfer. Once you get the hubs apart then the hub needs to be machined so...
... Or we're all not in the mood to talk about broken cars, having instead to deal with broken hearts and broken shuttles. dammit dammit dammit --Jay W....
i took the gt to the track today. not too bad considering i am in serious need of rings and some valve work. i had trouble finding a good rpm to launch at. in...
I concur, altogether a sad day. Think I'll take a consolation drive. Jim L8APEX MR2 2MCHFUN RX2 KILLER-B 323GTX (if available)...
WalkerJim@...
Feb 2, 2003 3:18 am
38034
Hello guys! Let me greet our brothers from Capri XR2 owners. I have a question for you what is the most popular Boost controller you guys use? What method of...
The problem I see is that I need a seat track that is capable of a accident and holds true to OEM crash specs. The OBX seats I looked at have 4 very large bolt...
Hello Group, Today at Vishnu, I did 4 passes on the Dyno. Low boost, at the wheels, I recorded 124 HP at 5600 RPM and ~ 124 ft lbs of Torque at 4750 RPM. High...
Hey Terry nice seeing you at the meet today! I am glad you had fun and I was very impressed with your cars performance. Especially in light of the many DSM...
i have just picked up a 1990 GTX front bumper and strut bar as well as a BFMR front bumper off a friend. for free :). now the BFMR bumper is a spare for me,...
Hi, I've only just started reading this site so I may be passing on information you all know. To convert to coil over suspension you need to get hold of...
CRE Hamilton
cdncre@...
Feb 2, 2003 3:04 pm
38042
Yet another Hamilton area GTX person pops up! I've actually lost count of how many GTX and GT's I've sighted from here (Hamilton) to T.O to Kitchener. Welcome...
So you are at about 160+hp at the flywheel. So what boost where you running at high setting? Greg Downing Washington State, USA gpd323@... ... From:...
160+?? This has to be 323GT I assume... GTX would be closer to 200 Jaroslav '91 GTX ... running at high setting?...
Jaroslav Sadovski
jaroslav.sadovski@...
Feb 2, 2003 6:01 pm
38045
Hey gang, I'm chuffed today cause I had a go at changing, front pads, discs and rear pads. Apart from the 10hrs spent doing it and the earache I got from the...
Well I am assuming 20% drivetrain loss? The GTX is supposed to make near 195HP at 16 psi. Maybe Terry's high boost setting is less than 16psi?? Terry??? Greg...
Also the GT uses the same motor as the GTX so they should if prepared the same make the same HP except that more drivetrain loss goes to the GTX. Greg Downing ...
When you bleed the brakes you must never let the brake fluid reservoir run empty. Always stop during the bleeding process to top off the reservoir. You must...
The rear caliper piston does indeed need to be turned into the caliper so you can fit new pads. You did that correct. Manual even says to use a pair of needle...
Sorry about that, I was getting ready for bed and was not thinking clearly. Low Boost: 10 psi High Boost: 14 psi The engine is fairly stock, mild porting on...
Oh yeah, I'm running the high boost at 14 psi (the lowest I can get the high boost setting) because I reckoned that it's the safest thing to do if I am using...
Any DOT 5 fluid is fine. You say you removed the hubs to replace the brake pads at the front? Or did you mean the front rotors were replaced? Pads at the front...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
