Ray - try _www.victorylibrary.com_ (http://www.victorylibrary.com) and look at the Master Engine Data Table for deck heights and such. There is also charts...
And I thought that was just a lot of book listings! Thanks Joey... I'm actually documenting a lot of stuff on the Polys for the Forward Look forum guys. I've...
Dave Stragand, who authors the Forward Look Website has set up a link through PayPal for donations. It's: www.ForwardLook.net PayPal is really secure for...
does anyone know what dampner I should use with the 360 crank, in my soon to be stroker Poly project.? even though I'll be getting the rotating assembly...
Sky, how's it going? I'm ok. Too much work! Anyway, you can use any LA style dampner/balancer you'd like, as long as you bring it to your reputable machine...
Schuyler - You will need a "zero balance" damper since you're getting the rotating assembly balanced. Good idea on getting the motor balanced, not only to...
Tom is right. Last night our cruise 50/50 raffle was $240. The club matched this number for a donation of $480. The gentleman who won the 50/50 returned his...
I have a 1961 Plymouth Wagon with a 318 and 14 inch wheels. It is an all stock car. I want to put 15 wheels on it with WWW radials, but want to keep my...
you may have to spend a bit of money, but a wheel modification shop could put 15 inch rims onto your original 14" centres. this is an easy job for them, but...
in my opinion, i would use the stock 360 spec. (external balanced) balancer and flywheel. provided that all you ever replace it with is stock 360 stuff, and...
I think if your building a stroker the motor will have to be balanced. Isn't "internal balance" just the same name for a balanced motor? Since the motor...
internal balance and external balance - the difference between the two is that internal is counterbalanced with only the weights on the crank and external has...
Indeed... they make deep well 15" rims that have the central well (the depression between the beads) half an inch deeper all round to enable them to be welded...
Say is there any newer 727 trannies that'll fit a 64 318? Or in that case any model or tranny that'll bolt up? I'm tryin' to find one with actual shift linkage...
Danny, there's a 65 torqueflite on ebay that isn't a pushbutton style and it'll fit my poly, but may not fit yours. From what I understand,the bellhousings...
I used a late model 727 (around a 70-71) in my 65 Coronet. With the post 65 727, you also have to convert to the linkage style for the shifter (post 66...
Yes, I have a 70 E body trans that's going in my 65. I had to get a trans mount from Schumacher, and I'm using a B&M floor shifter. You also have to get a...
I used the original flexplate. Torque converter bolted right up to it. "You also have to get a new flex plate because the old one won't work on the newer...
Well, don't know what to tell you...I tried it and it didn't work. Maybe I just got a smaller TC (went to a 10"), but the poly flex plate didn't bolt up it. ...
Speaking of modern transmissions does anyone know if the Keisler 5 speed manual overdrive will fit the Poly. Keisler lists the 62 to 65 B body as one of their...
It probably will with all the adapters out. I am pretty sure(not positive) that from 62 up the LA style trannys fit. Put in that 5spd with a Dick Landy...
Hello fellas: I have a 62 bombardier (15 pass Snow Coach ) that was manufactured in Valcount Quebec, came with optioned Canadian Poly 313. Talked to Bob A ...
The steel gaskets will work fine, I have a set on mine. I used the fel-pro gasket sealer(a REAL THIN layer) around the water ports and also where the steel...
hey Shaun, very cool Poly pics! Like the decal. (o; Way back, when I first got my Weiand 7503, I used the steel Fel-Pro gaskets and although it seemed to work...
How would you guys rate stainless versus hardened steel (arp for example) for engine and accessory bolts/studs/etc.? Are there grades to stainless? There...
Hey Ken- I put up a page from installing my Weiand intake...here it is if it helps any: http://www.mascotgraphics.com/4_barrel.htm I used the steel FelPro...
Michael, I did a search on Napa's site for the part number C-25487 which you had next to the heater fitting required for the Weinand swap. This part number...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
