It bolted in place with no modifications whatsoever. Set up with 100 main, 48 pilot, and pilot screw 1.5 turns out, with idle set a tiny bit fast. Bike has...
"It bolted in place with no modifications whatsoever." I know sometimes when fitting a large carb, it is necessary to match the carb box opening with the new...
For sale a barely used, cobalt blue 2004 Vespa ET2 (50cc). Package includes 2 helmets, silver armored jacket and scooter cover. $2000 or best offer. Photos...
M. Lambert-Williamson
iadair2@...
Feb 4, 2007 9:08 pm
28912
My PX is 5 and is in need of a makeover. First up, new wheels, the old uns had the paint flaking off the rust, with new tyres, S83's & tubes. The battery is...
Hello Mike Just going through a similar project with mine hoping to get this one way beyond 50,000 miles try Beedspeed for your parts they seem to have most of...
I want to paint my Super, because of the cost, I'm going to paint it myself either using spray cans or borrowing a compressor. To prep, I was going to get it...
How rusty is it? I would just clean it up the best you can, ralle can rust paint primer inside and out and the ratle can your colour of rust paint to finish. ...
Don't know about dip. Most people go for powder coat. At least that way you can mask any surfaces that should remain unpainted i.e. threaded bolt holes,...
Rust isn't major, on the floorboard, and wherever there are scratches. Just surface rust. I just wanted to make sure it wasn't going to rust from the inside...
On behalf of the Vulcans...I' d like to thank everyone for coming out to Vice City 2007 - Grand Theft Scooter this past weekend. We really did put alot of hard...
I want to install a cylinder kit on my 2 port Super. Down the line when I rebuild the engine I will be creating the 3rd port. I heard the DR180 is the best...
Thats what I want to do, but I figured if I split the case, I should just go ahead and do the rebuild. And right now I don't the time to do it. Mark ... ...
I was just told by someone that later model engines were 3 port. Is there a way I can tell without removing the head? It's a '76 Super. ... Celebrate the...
The only way to confirm, other than trusting that a '76 should be 3-port by default, is to pull the head, life up the cylinder and look to see whether the 3rd...
I have a 2005 Venice LX 49cc 2-cycle scooter I just bought used. I know they are under-powered due to their size, but I find that mine to be extremely...
... Valves?? In a 2-stroke? How is vacuum connected to fuel delivery? You may have a fuel delivery problem, but most likely caused by dirt/crud between the...
Full speed on that bike is 30mph. What speed are you obtaining? Lurching is either a fuel blockage (dirt or rust in tank, block air filler, bad vacuum line,...
I'm in the process of installing new inner and outer gear change cables on my 03' Stella frame that has the 200 cc LML motor in it. OE cables somehow got...
My general response to all concerns about scooter powering up is, "Why bother? It's a scooter, fer Heaven's sake!" If you wanna go fast get a Hyabusa. ... ...
Doug, check out www.provoscooter.com. They have performance and stock parts for 50cc scooters, including TNG. Just click on the TNG link on the left hand...
I've always found that it's just easier to run the cables solo without the old ones in place. Using the old cables as a guide is just a sure way to waste time...
Hi, recently bought a '81 p200e. Its pretty much completely original, so unmolested but some parts are tired. If I rev it and let go of the throttle, it...
... without the ... way to ... ~~~John, The problem I'm having is, I can't get one of the old cables out. I'm pulling it from the back of the frame and it...
Hello One at either end of the cable, check the cable for rust fraying etc or just replace it. Regards Barry--- In 2StrokeSmoke@yahoogroups.com, "David D"...
Hello The standard italian cables have the alloy bridge piece on the cables its to make sure that the right outer cable is offered up to the headset, they are...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
